background image

 

11 

Appendix LEDs and ports 

LEDs 

Figure 7

 

LEDs on the AP 

 

(1) Power LED 

(2) Radio LED 

(3) Ethernet uplink LED 

(4) Ethernet downlink LEDs 

 

Table 3

 

LED description 

Power LED 

Ethernet 

uplink LED 

Radio LED 

Ethernet 

downlink LED  Description 

Steady off 

Steady off 

Steady off 

Steady off 

The AP is not powered up or the LEDs are 
turned off by commands. 

Steady orange  Steady off 

Steady off 

Steady off 

Faults occur during the AP initiation. 

Flashing green 
(0.5 Hz) 

Any status 

Steady off 

Any status 

The AP is starting up. 

Flashing green 
(1 Hz) 

Steady off 

Steady off 

Steady off 

The AP is obtaining its IP address. 

Flashing green in turn 

Steady off 

The AP has obtained its IP address and is 
searching for ACs. 

Steady green 

Flashing green in turn 

Steady off 

The AP found an AC and is registering on 
the AC. 

Flashing green in turn 

Steady off 

Steady off 

The AP is performing the Ethernet uplink 
negotiation. 

Steady green 

Steady off 

Any status 

Any status 

The Ethernet uplink port is not connected 
with a network cable or has no traffic. 

Steady green 

Flashing 
green 

Any status 

Any status 

The Ethernet uplink port is sending or 
receiving data at 1000 Mbps. 

Summary of Contents for WA4320H-ACN






















Reviews: