094278_t_de_gb_fr_es_it_pt_eseilwi_s
haacon hebetechnik gmbh – T49 (0) 9375 - 84-0 – Fax +49 (0) 9375 - 84-66
19
The following is prohibited:
Transport of passengers
Persons standing under lifted loads.
Note: Warn persons in the immediate vicinity.
We refer to the applicable German accident preven-
tion regulations and, for use outside GERMANY, to
the respective national regulations!
Touching the drum and rope intake during operation.
Work on live components.
Never:
– Loop the rope around the load.
– Pull the lifting rope over stationery parts or edges.
– Exceed the permissible load-carrying capacity.
– Manipulate safety devices.
– Pull or drag loads diagonally.
– Wrench jammed loads away.
– Unreel rope to rope attachment. Two coils must always
remain on the drum.
– Work with untensioned rope operate without safeguard
against jumping off the drum.
– Work without lifting limiter.
Avoid to ensure operational reliability:
– Continuous operation, as well as continuous inching ope-
ration, exceeding of the duty cycle of the motors, as well as
remaining service life according to drive group and load.
Check before lifting the load:
z
Is the load suspended safely in the load hook and is it com-
pletely accommodated in the hook? Is the safety flap closed?
For attaching the load, the respective national regulati-
ons for load carrying devices apply (in Germany the
DGUV-R 100-500, Chapter 2.8).
2.4 Safe Storage, Transport, and Assembly
Store clean, dry and protected. Take measures against corro-
sion on wire rope, hook and brake.
Transport and assembly by authorised persons, familiar with
the valid safety and accident prevention regulations as well as
with the operating instructions.
Please check:
z
Are there any transport damages ? (Immediately notify the
supplier).
z
Is personal protection equipment worn? (Safety glass, safety
shoes, if necessary helmet).
z
Are suitable, standardised and examined hoisting gear and
load securing devices used ? Dimensions and weights
–> technical data (Chapter 3.3).
Always:
– Only fasten load securing device to base plate, gear, drum
and/or drum shaft.
– Transport device protected against impacts and shocks,
falling over or toppling.
– Assemble on stable, flat surface.
– Attach the device such a way, that neither the load nor other
effects can change the position the position.
2.5 Save Service / maintenance, Troubleshooting
Always observe the intervals specified or indicated in the ope-
rating instructions for recurring tests/inspections.
All persons, who work on the device must be suitable for this
purpose, familiar with the valid safety and accident protection
regulations and have been assigned by the operator.
Before starting special and maintenance measures:
z
Have persons in the danger zone been informed and warned?
Areas shut off?
z
Is the device load-free and sufficiently cooled down?
Has the main switch been switched off and the
device safeguarded against unexpected restar-
ting? (Actuate emergency stop, close main switch
and attach warning signs) Manual interventions in
an operating device can lead to severe accidents.
If switching on is nevertheless necessary (e.g. rope
replacement), then this may only be carried out
while observing special safety precautions.
– Is suitable protection equipment worn and have appropri-
ate protective measures been met, if required? (e.g. falling
protection when working at large heights)
– Have possibly released screw connections being tightened
safely again?
– If necessary safety devices have been disassembled, have
they been reassembled, examined, and documented imme-
diately after concluding work?
– Are operating and auxiliary materials disposed safely and in
an environmental-friendly manner?
2.6 Safety Instructions Electrical Equipment
Disconnect from the power supply when working on the electri-
cal equipment.
Only permit authorised specialists to work on the electrical
equipment. And electrical specialist is a person with suitable
training and experience, as well as knowledge of the relevant
regulations, who is able to recognize risks and avoid dangers,
caused by electricity.
Always keep control cabinets closed.
Never:
Work on live parts.
During inspection, maintenance, and repair work:
z
Disconnect device from power supply, safeguard against
restarting
z
First check that electrical components are disconnected
from the power supply, then ground and short-circuit them,
and finally insulate live neighbouring components.
z
Always work with a second person, who when working on
live components (exceptional case) can actuate the emer-
gency stop button or main switch in case of an emergency.
Use only voltage-insulated tools.
– Always replace fuses by fuses of the same type with the
specified amperage.
– Never bypass fuses!
– Do not carry out any constructional and safety reducing mo-
difications to the control units.
– Guarantee perfect grounding of the electrical system by a
protective conductor system.
2.7 noise Protection
Noise does not represent a significant danger with this device.
Values –> technical data (Chapter 3.3).
Hearing protection can nevertheless be necessary according
to the local conditions.
GB
