background image

 

Dear Customer!

 

 

 

Congratulations and thank you for choosing Haas+Sohn solid fuel stove; 
hope that it will please you for many many years. 
You bought a solid fuel stove equipped with an innovative heating system, 
which burns the prescribed fuel in an environment friendly and economical 
way. To comply with the strict regulations of emission values, it requires a 
precisely 

metered 

supply 

of 

combustion 

air.  

This dosage can be reached with the automatic

 power control, which helps 

the  warming  up  and  closes  automatically  after  reaching  the  operating 
temperature.

 

A combined heating and ashdoor offers you more ease of access and a 
major increase in safety (no uncontrolled burning through an open ash 
door). It is particularly important to have a professional and elaborated 
connection to an operating chimney.  

 

 

Table of Contents

 

 

Equipment Safety Act

….…...…2

 

General 

…………….………….…3 

Disposal of packaging  
Safety notice 

……………………4  

Device components

 

-Dimensions/ Mounting dimensions.

Technical specifications 
Installation instructions

……...6 

Exhaust stack

 

-Mounting the smoke outlet on top 

Connection to the chimney……….7 
Connection for the external 
combustion air supply 

….…….8

 

Controls 

……………………….10

 

-Air regulation 
-Air draught limiter 
-Height adjustment 
-Cleaning cover 

………………..12

 

-Combustible drawer 

Oven 

…………………………... 13

 

Starting up

…………………….14

 

-Combustibles 
-Emission control 

 

 
 

Heating 

………………………….15

 

-Heating mode 
-Heating with wood 
-Heating with coal 

Cooking 

…………………………16

 

-Baking and roasting 
-Oven thermometer 

Cleaning and maintenance 

…. 17

 

Glass ceramic stove top

….……18

 

-Safety was priority during 
production and construction 
- During cleaning the 
following principles must be 
observed 
-Implementation, cleaning 
and maintenance of the 
stove top 

 Faults, failure analysis

……….19

 

-Faults and failure analysis 
-Standard operation 

The chimney

…..………………..21 

Notes

……………………………..22

 

Summary of Contents for HSDZ 75.5-SF easy

























Reviews: