background image

 

7.3.  Using for the first time 

7.3.1. General: 

Before using for the first time 

 

Remove any stickers. 

 

Remove all accessories from the pellet tank and the  
combustion chamber. 

 

Check whether the combustion chamber cladding (see appliance sheet - combustion chamber 
replacement part Figure 8a) is attached to its fastenings. This could have slipped out of its position as a 
result of the transportation or installation of the stove.  

 

Check that the burner fits perfectly in its mounting. 

 

Close the combustion chamber door. 

 

Fill the storage container with pellets 

 

Plug in mains cable 

 

Tip!! 

Only

 when 

using for the first time

, place approx. 30 pellets in the burner. This speeds up the ignition process. 

7.3.2. Operating console: 

7.3.2.1. Software version 

 

As soon as the mains plug is connected, the software version appears on the display for approx. 7 seconds, 
e.g.: 

Software HSP-6-V5.03

 

7.3.2.2. Language selection 

After that you can select your required language. 

Procedure:

  

The required language is selected with the 

“Plus”

 or 

“Minus”

 buttons and confirmed with 

“OK”

7.3.2.3. Welcome page 

28°C



                 23°C



     

                            off

on

menu

10:34

 

  OK 

>deutsch                          <
 englisch            

language

language

Summary of Contents for HSP 6 PALLAZZA-III 519.08



















Reviews: