habitat et jardin 91 cm, Assembly Instructions Manual

1.

To prepare the Ladder Handle Assembly (see 

Fig. 1

), the Machine Screws should be installed from the

inside of the Ladder Hinge and then through the Ladder Handle 

2

, and out through the Ladder Brace

with the safety label on the outside. Make sure that the English warning label is facing out on both handle

sections. Install the Lock Washer, and thread the Cap Nut on until the Ladder brace tightens up against the

Handle

2.

The Machine Screws 

6

 should be installed from the inside of the Ladder Handle 

2

, and out through the

Ladder Handle. Install the Flat Washer, , Lock Washer, and thread the Cap Nut on until the Ladder Brace

tightens up against the Ladder Handle. (See 

Fig. 1

)

3.

To prepare the Ladder Leg Assembly (see 

Fig. 2

), start with one “R” ladder leg section. Carefully pre open

one Ladder Step Clip from the side, just enough to get over the top section of the Ladder Leg, and slide it

from the top of the leg down to the lowest indented section as shown in the 

Figure 2

. The ridge on the

Ladder Step Clip should be on the inside of the leg as shown in the 

Figure 2

. Repeat the same process to

make the left “L” ladder leg section

4.

Slide a Ladder Step down over both legs. Make sure that the side of the stop marked with an “R” is on

the right side leg. Slide the stop down until the ladder step clips inserts into the underside of the stop and

the ridges inside of the clips lock into place. The ladder step clips should stay in the indented section of

the ladder leg as you press the steps down over them. The ladder step clips should insert flush against the

bottom of the step. (See 

Fig. 3

).

5.

To prepare the Swivel Ladder Leg Assemby (see 

Fig. 4

), start with one Straight Ladder Leg. Carefully pre

open one Ladder Step Clip from the side, just enough to get over the top section of the Straight Ladder Leg,

and slide it from the top of the leg down to the lowest indented section as shown in the 

Figure 4

. The ridge

on the ladder clip should be on the inside of the leg as shown in the 

Figure 4

. Repeat the same process to

make another Straight Ladder Leg section.

6.

Slide a Ladder Step down over both Straight Ladder Legs. Slide the step down until the Ladder Step Clips

insert into the underside of the stop and the ridges inside of the clips lock into place. The Ladder Step Clips

should stay in the indented section of the Ladder Leg as you press the steps down over them. The Ladder

Step Clips should insert flush against the bottom of the step as shown in the 

Figure 5

.

7.

Place the Swivel Ladder Clamp with Button at the topmost step of the Straight Ladder Leg as shown in

the 

Figure 4

. The button should be installed facing outwards and the lock should be pointing to the front.

The Swivel Ladder Clamp is installed on the other side of the Straight Ladder Leg as shown in the 

Figure 4

.

The small clamp should be pointing to the front.

8.

The Machine Screws should be installed from the inside of the Straight Ladder Leg 

13

. Thread the Cap Nut

on until the Swivel Ladder Clamp tightens up against the Straight Ladder Leg. (See 

Fig. 5

).

9.

Place the Ladder Bottom Clips at the bottom of the Straight Ladder Leg as shown in the 

Figure 4

. The

Machine Screws should be installed from the Inside of the straight ladder leg. Thread the cap nut on until

the ladder bottom clips tighten up against the straight ladder leg (see 

Fig. 4

).

10.

Stand the Ladder Leg Assembly in the upright position, with feet facing outward, as shown in the

Figure 6

. Place the ladder handles, with the Ladder Braces on the outside of the ladder, on top of both

ladder leg sections.

11.

Make sure all of the steps are now level (parallel to the ground.) If one section is different, lift the handles

and turn the ladder leg section around. Re-install handles and push down tightly.

12.

From the inside of the Ladder Handle, insert the two Machine Screws through the Flat Washers, then

through the Ladder Handle and fasten in place using the two Lock Washers  and Cap Nuts . (See 

Fig. 6

).

13.

Stand the Left and Right Plain Ladder Leg in the upright position, with feet facing outward, as shown in

the 

Figure 6

.

S E T   U P   I N S T R U C T I O N S

-

2

-

-

15

-