Troubleshooting
PROBLEM
POSSIBLE CAUSE
PREVENTION/CURE
Wires or Electrode covered with
cooking residue
Clean wire and/or electrode with rubbing alcohol
Electrode and burners are wet
Wipe dry with cloth
Electrode cracked or broken –
sparks at crack
Replace electrode
W ire loose or disconnected
Reconnect wire or replace electrode/wire assembly
W ire is shorting
(Sparking
between igniter and electrode)
Replace igniter wire/electrode assembly
Burner will not light
using igniter
No gas flow
Check if LP gas cylinder is empty. If empty, replace or refill,
or else refer to “sudden drop in gas flow or reduced fl ame
height”
Coupling nut and regulator not
fully connected
Turning the coupling nut about one-half to three quarters
additi onal turn until solid stop. Tighten by hand only, Do not
use tools .
Obstruction of gas flow
Clear burner tubes, check for bent or kinked hose.
Spider webs or insect nest in
venturi
Clean venturi
Burner ports clogged or blocked Clean burner ports
Out of gas
Replace or ref ill LP gas cylinder
Sudden drop in gas
flow or reduced
flame height
Excess flow, safety device may
have been activated
Turn control knobs to
, wait 30 seconds and light
barbecue. If flames are still too low, reset the excessive flow
safety device by turning control knobs
and L P gas
cylinder
valve to “CLOSED” Disconnect regulator . Turn
control knobs to “HIGH ”, wait 1 minute. Then turn control
knobs to , and reconnect regulator and leak check
connections . Slowly turn LP gas cylinder valve to “OPEN”,
wait 30 seconds and then light barbecue per lighting
instruction s.
Burner
ports are clogged
or
blocked
Clean burner ports.
New burner may have residual
manufacturing oils
Burn barbecue for 15 minutes with the lid closed
Spider webs or insect nest in
venturi
Clean venturi
Food
residue, grease or
seasoning salt on burn er
Clean burner
Poor alignment
of valve to
injector venturi
Assure burner venturi is properl y engaged with injector
High or gusting winds
Do not use barbecue in high winds
Low on LP Gas
Replace or ref ill LP gas cylinder
Excess flow valve tripped
Reignite the BBQ
Grease trapped by food buildup
around
burner system
Turn control knobs to
, Turn L P gas tank v alv e to
“CLOSED”.
Leave lid in open
position and let fire burn out.
After barbecue cools, remove and clean all parts
Flashback (fire in
burner tube(s)
Burner and/or burn er tubes are
blocked
Clean burner and/or burner tubes
Inside of lid is peeling
(like paint peeling)
The lid is stainless steel, not
painted
Baked on grease bui ldup has turned to carbon and is flaking
off. Clean thoroughly.
Burner will not light
with match
Irregular flame
pattern, flame does
not run the full
length or burner
Flame is yellow or
orange
Flame blow out
Persistent grease
fire
OFF "
"
OFF "
"
OFF "
"
OFF "
"
13
Summary of Contents for Festa 5
