3.3 Connect the probe to the controller
Connect the sensor cable to the quick-connect fitting of the SC Controller. Keep the device connector
caps for future use. Refer to
. Refer to the controller documentation for more information.
Note: Extension cables are available if a longer cable is necessary.
Figure 6 Connect the probe to the controller
Section 4 Startup
Connect the power cord to an electrical outlet with protective earth ground or set the circuit breaker
for the controller to on.
Section 5 Operation
5.1 User navigation
Note: Refer to the controller user manual for the keypad description and navigation information.
5.2 Configure the probe
Enter identification information, configure the measurement and change options for probe settings,
data handling and storage.
1.
Make sure that the controller has the latest software installed. Refer to the controller user manual
for more information. (For the SC200 Controller, the minimum version is 2.06.)
2.
Go to the device menu as follows:
• SC200 and SC1000 Controllers—Go to the main menu, then select
Sensor setup
. If
applicable, select the sensor.
Note: For older versions of the SC200 controller, select the Single measurements only setting.
• SC4500 Controller and Claros interface—Select the tile of the device, then select
Device
menu
.
3.
Select
Configuration.
English
13
Summary of Contents for NT3100sc
