background image

 

 

 

 

5.52.653.01.01.04 

 

 

 

2.3 

Requirements for the operating personnel 

  The units may only be operated by qualified persons that are appropriately trained and that are familiar with 
it. They must have their employer’s authorization for operation of the units. 
Before  starting  work,  the  operating  personnel  must  have  read  the  operating  and  installation  instructions, 
especially the chapter "Safety Instructions". 

This  is  especially  important  for  operating  personnel  that  rarely  uses  the  equipment,  i.e.  for  installation  or 
maintenance work. 

   

DANGER!

 

In order to avoid severe injury, please pay attention to the following when using the equipment: 

  Use protective clothes/equipment. 

  Do not wear long hair hanging down open. 

  Do not wear rings or other jewelry. 

  Do not wear clothes that are too big/wide. 

  Do not reach into ropes, chains, drive parts or other moving parts with your hands 

 

 

2.4 

Appropriate use 

The permitted safe working load of the devices must not be exceeded! An exception can be made during the 
load test before initial operation, carried out by a licensed qualified person. 

 

 

  Defective  devices  and  load  suspension  devices  must  not  be  used  until  they  have  been  repaired!  Only 

original spare parts must be used. Non-compliance will result in any warranty claims becoming void. 

  Liability and warranty will become void if unauthorized modifications of the units are made by the user! 

  The permissible ambient temperature when operating the devices: 

Power unit 

Device classification for 

Not explosive atmosphere 

Explosive atmosphere 

according to  

 ATEX 

)* )**

 

Manual 

-20°C/+50°C 

-20°C/+40°C 

Motor 

-20°C/+40°C 

-20°C/+40°C 

 

) * At an atmospheric pressure range from 0.8bar to 1.1bar and an oxygen content of approx. 21% 

) ** Devices of this category have been specially modified and labeled by the manufacturer

 

   

DANGER!

 

The permissible ambient temperature must not be exceeded! 

 

  Moving horizontally on beams. 

 

 

   

DANGER!

 

The use is not allowed: 

  for pulling loose of stuck loads, dragging of loads and inclined pulling. 

  in explosive atmosphere, except the unit is especially modified for it and marked by an indication label. 

  in reactor containment vessels. 

  to transport people. 

  The device is not suitable for use on stages and in studios. 

Persons must not stand under a suspended load. 

 

 

 

 

NOTICE!

 

If the units are not used appropriately, it is not possible to ensure safe operation. 

The  owner  and  operator  have  sole  liability  for  all  personal  injury  and  damage  to  property  arising  from 
inappropriate use. 

 

 

 

   

DANGER!

 

It’s  only  allowed  to  use  the  unit  in  the  EX-classification  which  is  named  on  the  type  plate; 
or in lower classes 

 

 

Summary of Contents for 19/90

















Reviews: