background image

 

 

 

 

10 

 

 

5.52.162.00.01.05 

 

Operation 

 

Only people that are familiar with the operation of the lifting devices and cranes may be entrusted with their 
operation. They must be authorized by the employer for the operation of the equipment. The employer must 
ensure that the operating instructions are available near the equipment and that they are accessible for the 
operating personnel.  

 

Lifting and Lowering by pulling the endless hand 
chain. 

 

Lifting - pull the chain fall at the right side 

–  

the hand chain wheel turns clockwise 

 

Lowering - pull the chain fall at the lift side 

–  

the hand chain wheel turns anti-clockwise 

 

Illustration5 

 

 

  

NOTICE!

 

For double lifting mechanism 

Operate both lifting mechanism, synchronous resp.evenly. 

 

 

 

   

CAUTION!

 

Run in of chain into the chain container for hoist with double lifting mechanism 

For a correct run in of chain into both chain containers, the lowering operation must be carried out, without 
load, at certain intervals, until both chain container are empty. 

 

For motorized devices with operating limit switches "lowering" 

Lower until the operating limit switch is released. 

 

Non-observance can lead to device damages! 

 

 

   

WARNING!

 

The hoist must always hang centrally under the beam or under its suspension point. 

 

 

Monorail push travel trolleys are moved by pushing the load. 

Monorail hand geared trolleys are moved by pulling the hand chain. 

 

 

 

7.1 

Brake and pawl  

The brake system needs a minimum load of 3% of the capacity. 

Only  this  minimum  load  makes  sure  that  the  load-pressure-brake  closes  correctly.  When  the  brake  closes 
correctly, the load is safely held 

   

GEFAHR!

 

Working situations with no guarantee that the minimum load is charged, are forbidden! 

 

 

Commissioning 

 

8.1 

General 

Should the unit be used in Germany:  

Please observe the validated, national accident prevention regulations. 

For other countries:  

Inspections as above. Please observe the national rules and regulations and the instructions in this manual! 

 

 

Summary of Contents for 21/12


















Reviews: