background image

 

 

 

 

 

 

5.52.162.00.01.05 

 

Safety 

 

 

2.1 

Warning notice and symbols 

Warnings and notice are shown as follows in these instructions: 

 

 

  

DANGER!

 

This means that there is a high risk that leads, if it is not avoided, to death or severe injury. 

 

  

WARNING!

 

This means that there is a risk that could lead, if it is not avoided, to death or severe injury. 

 

   

CAUTION!

 

This  means  that  there  is  little  risk  that  could  lead,  if  it  is  not  avoided,  to  slight  injury  or  damage  to  the  device  or  its 
surrounding. 

 

NOTICE!

 

Gives advice for use and other useful information. 

 

 

Danger from electricity. 

 

 

Danger from explosive area. 

 

 

2.2 

Duty of care of the owner 

   

DANGER!

 

Failure to follow the instructions of this manual can lead to unpredictable hazards. 

For any resulting damage or personal injury, HADEF assumes no liability. 

 

The unit was designed and built following a risk analysis and careful selection of the harmonized standards 
that are to be complied with, as well as other technical specifications. It therefore represents state-of-the-art 
technology and provides the highest degree of safety. 

Our  delivery  includes  the  hoist  supplied  beginning  at  its  suspension  and  ending  at  the  load  hook  and  if 
supplied  with  control,  the  control  line/hose  that  leads  to  the  hoist.  Further  operating  material,  tools,  load 
attaching devices as well as main energy supply lines must be assembled according to the valid rules and 
regulations.  For  explosion-proof  equipment,  all  these  parts  must  be  approved  for  use  in  area  prone  to 
explosion, or they must be suitable for use in area prone to explosion. The owner is responsible for this. 

However,  in  everyday  operation  this  degree  of  safety  can  only  be  achieved  if  all  measures  required  are 
taken. It falls within the duty of care of the owner/user of the devices to plan these measures and to check 
that they are being complied with. 

Complete  the  operating  and  installation  instructions  by  any  instructions  (regarding  supervision  or 
notifications)that  are  important  for  the  special  kind  of  use  of  the  equipment,  i.e.  regarding  organization  of 
work, work flow and human resources. 

In particular, the owner/user must ensure that: 

  The unit is only used appropriately. 

  The  device  is  only  operated  in  a  fault-free,  fully  functional  condition,  and  the  safety  components,  in 

particular, are checked regularly to ensure that it is functioning properly. 

  The  required  personal  protective  equipment  for  the  operators,  service  and  repair  personnel  is  available 

and is used. 

  The operating instructions are always available at the location where the equipment is used and that they 

are legible and complete. 

  The unit is only operated, serviced and repaired by qualified and authorized personnel. 

  This  personnel  is  regularly  trained  in  all  applicable  matters  regarding  safety  at  work  and  environmental 

protection, and that they are familiar with the operating manual and, in particular, the safety instructions it 
contains. 

  Any safety and warning signs on the devices are not removed and remain legible. 

  Devices  for  use  in  area  prone  to  explosion  must  (from  customer's  side)  be  earthed  with  a  shunting 

resistor of < 10

6

 

Ω against earth. 

 

   

WARNING!

 

It is not allowed to make constructive changes of the equipment! 

 

Summary of Contents for 21/12


















Reviews: