background image

 

 

 

5.52.181.00.01.05  

 

5

 

However, in everyday operation this degree of safety can only be achieved if all measures required are 
taken. It falls within the duty of care of the owner/user of the devices to plan these measures and to check 
that they are being complied with. 
Complete the operating and installation instructions by any instructions (regarding supervision or 
notifications)that are important for the special kind of use of the equipment, i.e. regarding organization of 
work, work flow and human resources. 
In particular, the owner/user must ensure that: 

ƒ

  The unit is only used appropriately. 

ƒ

  The device is only operated in a fault-free, fully functional condition, and the safety components, in 

particular, are checked regularly to ensure that it is functioning properly. 

ƒ

  The required personal protective equipment for the operators, service and repair personnel is available 

and is used. 

ƒ

  The operating instructions are always available at the location where the equipment is used and that they 

are legible and complete. 

ƒ

  The unit is only operated, serviced and repaired by qualified and authorized personnel. 

ƒ

  This personnel is regularly trained in all applicable matters regarding safety at work and environmental 

protection, and that they are familiar with the operating manual and, in particular, the safety instructions it 
contains. 

ƒ

  Any safety and warning signs on the devices are not removed and remain legible. 

ƒ

  Devices for use in area prone to explosion must (from customer's side) be earthed with a shunting 

resistor of < 10

6

 

 against earth. 

Pos: 6.2.2.2 /1_HADEF/---ALLGEMEIN/Hinweise/WARNUNG - Keine konstuktiven Änderungen @ 0\mod_1176797173443_52.docx @ 4704 @  @ 1 

 

   

WARNING!

 

It is not allowed to make constructive changes of the equipment! 

6.2.3 /1_HADEF/2--SICHERHEIT/Allgemein/Anforderungen an das Bedienpersonal/05.Anforderungen an das Bedienpersonal @ 0\mod_1172055544978_52.docx @ 179 @  @ 1 

 

2.3 

Requirements for the operating personnel 

  The units may only be operated by qualified persons that are appropriately trained and that are familiar with 
it. They must have their employer’s authorisation for operation of the units. 
Before starting work, the operating personnel must have read the operating and installation instructions, 
especially the chapter "Safety Instructions". 
This is especially important for operating personnel that rarely uses the equipment, i.e. for installation or 
maintenance work. 

   

DANGER!

 

In order to avoid severe injury, please pay attention to the following when using the equipment: 

ƒ

  Use protective clothes/equipment. 

ƒ

  Do not wear long hair hanging down open. 

ƒ

  Do not wear rings or other jewellery. 

ƒ

  Do not wear clothes that are too big/wide. 

Pos: 6.3 /1_HADEF/2--SICHERHEIT/Bestimmungsgemäße Verwendung/01.Alle (außer 380) @ 2\mod_1300955165911_52.docx @ 18464 @  @ 1 

 

2.4 Appropriate 

use 

The permitted safe working load of the devices must not be exceeded! An exception can be made during the 
load test before initial operation, carried out by a licensed qualified person. 

 

 

ƒ

  The permissible ambient temperature during operation of manual driven devices is -20 ° C / + 50 ° C and 

at all power driven devices -20 ° C / + 40 ° C! 

ƒ

  Defective devices and load suspension devices must not be used until they have been repaired! Only 

original spare parts must be used. Non-compliance will result in any warranty claims becoming void. 

ƒ

  Liability and warranty will become void if unauthorized modifications of the units are made by the user! 

Pos: 6.4 /1_HADEF/2--SICHERHEIT/Bestimmungsgemäße Verwendung/02.Alle Kettenzüge @ 2\mod_1300955359453_52.docx @ 18468 @  @ 1 

 

The appropriate use of the hoists is vertical lifting and lowering of unguided loads. In combination with 
trolleys, loads can also be moved horizontally. 

 

 

Summary of Contents for 29/06AP Series




























Reviews: