background image

19

Maintenance of the remote control

Cleaning the remote control:  

Clean the remote control with a damp cloth and a neutral 
solution of detergent without abrasive substances. 

Changing the battery:   

• 

Open the battery casing. 

• 

Replace the flat batteries with 3 new 1.5 V type AAA 
batteries. 

 

Respect the polarity indicated in the battery casing when 
inserting the new battery! 

• 

Close the battery casing up again.  

Disposal of the batteries 

Ultimate disposal of the batteries should be handled according 
to all national laws and regulations. Do not place used 
batteries in your regular waste. 
Ultimate disposal of the batteries must be done safely

.

Contact your local waste management officials for other 
information regarding the environmentally sound collection, 
recycling, and disposal of the batteries. 

Operation anomalies

The hood does not work

Make sure that: 
• 

There is no current blackout 

• 

A speed has been effectively selected. 

• 

The panel is correctly hooked. 

• 

The 9-pole connection is well inserted (

Picture 9b

).

• 

The red reset key above the electric system box is 
pressed. 

• 

The wires in the 9-pole connection are well inserted into 
the connector. (During connection, exerting an 
overpressure may cause the contacts to bend). 

The hood has low efficiency 

Make sure that: 
• 

The motor speed selected is sufficient for the quantity of 
fumes present 

• 

The kitchen is aired enough to allow an air intake and the 
charcoal filter is not worn out (filter version hood). 

• 

The air outlet pipe is not clogged. 

• 

The suction unit non-return valves can rotate freely. 

The hood stops during operation 

Make sure that: 
• 

There is no current blackout 

• 

The differential magnetothermal switch (automatic circuit 
breaker) has not been released. 

Maintenance 

Cleaning

Clean using 

ONLY

 the cloth dampened with neutral liquid 

detergent. 

DO NOT CLEAN WITH TOOLS OR 

INSTRUMENTS

. Do not use abrasive products. 

DO NOT USE 

ALCOHOL!

Grease filter 

Traps cooking grease particles. 

This must be cleaned once a month (or when the filter 
saturation indication system – if envisaged on the model in 
possession – indicates this necessity)  using non aggressive 
detergents, either by hand or in the dishwasher, which must 
be set to a low temperature and a short cycle. 
When washed in a dishwasher, the grease filter may discolour 
slightly, but this does not affect its filtering capacity. 
When inserting and removing grease filters and charcoal 
filters, please make sure that the extractable unit of the hood 
is in open position .In order to do this,pull the 

OFF

 (

T5

)key. 

Then remove the front panel ,by pulling on the upper part of 
each side at the same time (

Fig.13

).

The panel turns forward ,so that grease filters can be inserted 
(

Fig.14

).

Charcoal filter (filter version only) 

It absorbs unpleasant odours caused by cooking. 

The saturation of the 

charcoal filter

 occurs after more or less 

prolonged use, depending on the type of cooking and the 
regularity of cleaning of the grease filter. 
In any case it is necessary to replace the cartridge at least 
every four months. 
The charcoal filter may NOT be washed or regenerated. 
After removing the grease filter, it is possible to insert the 
charcoal filters (

Fig. 15

) (

not supplied

).

Summary of Contents for HH-TVG90A
















Reviews: