Hafele HH-WVG80D, Instruction On Mounting And Use Manual

18

In the case of the presence of panels and/or walls and/or 
lateral wall units check that there is sufficient space to install 
the hood and that access to the command panel is easy. 

Only for some models  

An aesthetic flue can be purchased as an optional accessory. 
Check with the authorized dealer whether the model in your 
possession envisages this possibility.  
We advise installing the hood after having purchased the flue 
to check with certainty the most suitable installation. 

Fig. 5-14-15-16-17 

Operation 

Use the high suction speed in cases of concentrated kitchen 
vapours.  It is recommended that the cooker hood suction is 
switched on for 5 minutes prior to cooking and to leave in 
operation during cooking and for another 15 minutes 
approximately after terminating cooking.  

T1.  Lights ON/OFF  
T2. Speed decrease 

 Press 

"T2"

 button to decrease the speed from 4 

(intensive) to  1. 

 Press 

"T2"

 button during operation at speed 1, the hood 

sets to OFF. 

T3 Speed 

increase 

 Press 

T3

button and the hood sets from OFF to speed 1. 

Press the button (hood ON) to increase the speed of the 
motor from 1 to 4 (intensive). 

The respective LED goes on for each speed. 

Speed 1

 - LED 

1

Speed 2

 - LED 

2

Speed 3

 - LED 

3

Speed 4 (Intensive)

 - LED 

4

(flashing) 

The intensive speed is timed. Standard timing is 5’, at the 
end of which the hood sets to speed 2. 

To deactivate the function before time is up press 

T2 

button, the hood sets to speed 3. 

T4 Speed 

timing 

Speed timing is activated by pressing 

T4 

button, when 

timing is up the hood switches off. 

Timing is divided as follows: 

Speed 1

 - 20 minutes (LED 

1

 flashing) 

Speed 2

 - 15 minutes (LED 

2

flashing) 

Speed 3

 - 10 minutes (LED 

3

 flashing) 

Speed 4 (Intensive)

 - 5 minutes (LED 

4

 flashing) 

During timed operation press 

T2

 button and the hood quits the 

timed mode and decreases the speed. 
Press 

T3

 button and the hood quits the timed mode and 

increases the speed. 
Press 

T4

 button and the hood quits the timed mode 

maintaining the set speed. 

Grease filter signal 

After 40 hours of operation LED 

1

 flashes. 

When such signal appears the grease filter installed needs to 
be washed. 
To reset the signal, keep 

T4

 button pressed for 5”. 

The hood gives out a "BEEP" and LED 

1

 stops flashing. 

Charcoal filter signal 

After 160 hours of operation LED 

2

 flashes. 

When such signal appears the charcoal filter installed must be 
replaced. 
To reset the signal, keep 

T4

 button pressed for 5”. 

The hood gives out a "BEEP" and LED 

2

 stops flashing. 

In case of contemporaneous signalling of both filters, LEDs 

1

and

 2 

flash alternatively. 

To reset, carry out the procedure described above for 2 times. 
The first time it resets the charcoal filter signal, the second 
time it resets the grease filter signal. 

The charcoal filter signal is not active in the standard mode. 
In case the hood is used in filter version it is necessary to 
enable the charcoal filter signal. 

Activating charcoal filter signal: 

Set the hood to OFF and press 

T4

 button for 5”. 

Once the button has been pressed, the LEDs related to the 
filter signals currently active light up. 
The hood gives out a "BEEP" and LED 

2

 flashes for 2". 

LEDs

1

 and 

2

 remain on for about 2" before the hood goes 

back to OFF. 

Deactivating charcoal filter signal: 

Set the hood to OFF and press 

T4

 button for 5”. 

Once the button has been pressed, the LEDs related to the 
filter signals currently active light up. 
The hood gives out a "BEEP" and LED 

2

 switches off. 

LED

1

 remain on for about 2" before the hood goes back to 

OFF.