THUMB TURN
ASSE
LATCH MOUNTI
L
DEAD
STRIKE
WOOD FRAME
REINFORCER
DUST BOX
FOR USE ON DOORS 1-3/8" to 1-3/4"
(35mm-45mm) THICK
TOOLS REQUIRED FOR NEW INSTALLATION:
(1) Phillips Head Screwdriver
(1) 2-1/8" (54mm) Hole Saw
(1) 1" (25.4mm) Drill Bit
(1) Chisel
TOOLS REQUIRED FOR REPLACEMENT INSTALLATION:
(1) Phillips Head Screwdriver
FOR REMODELING OR NEW CONSTRUCTION:
- Follow all steps
3220/3222 Thumbturn Only Deadbolt
Installation Instructions
FOLD HERE
ON DOOR EDGE
1-3/8"
35
45
1-3/4"
T E MP L AT E
1-9/16"
40
2-1/8" (5 mm) HOLE
4
Make 1"(25.4mm) hole at center
of door edge.
2-3/8" ( 60mm
))
BACKSET
2-3/4" ( 70mm
))
BACKSET
1. MARK DOOR
2. DRILL HOLES
3. PREP DOOR
2-1/8" (54mm) HOLE
1-3/16" (31mm) DEEP
1"(25.4mm) HOLE
4-1/8"(105mm)
DEEP
DOOR FACE
DOOR EDGE
2-1/8" (54mm) HOLE
1"(25.4mm) HOLE
DOOR FACE
DOOR EDGE
2-1/8" (54mm) HOLE
1-3/16" (31mm) DEEP
1"(25.4mm) HOLE
4-1/8"(105mm)
DEEP
DOOR FACE
DOOR EDGE
2-1/8" (54mm) HOLE
1-3/16" (31mm) DEEP
1"(25.4mm) HOLE
4-1/8"(105mm)
DEEP
DOOR FACE
DOOR EDGE
Measure center line of lock; height as desired from finished floor.
Select 2-3/4" or optional 2-3/8" backset, fold and apply template
to interior side of door and mark center of door as indicated on
template. Mark center hole on door face through guide on template.
(See Step 6 for changing latch backset)
Drill 2-1/8" (54 mm) hole through door face as marked for deadbolt.
(It is recommended that holes be drilled from both sides of the
door to prevent splitting). Drill 1” (25.4 mm) hole in center of
door edge for latch.
Insert latch in hole, keeping latch face parallel to
face of door edge.
Mark outline and remove latch.
Chisel 5/32" (4 mm) deep or
until latch face is flush with door edge.
a.
b.
REV.
DESCRIPTION
ECO NO.
DATE
WEIGHT: 0.73
3200 SERIES DEADBOLT
-
Material <not specified>
-
-
-
-
-
PROPRIETARY & CONFIDENTIAL
THE INFORMATION CONTAINED
IN THIS DRAWING IS THE SOLE
PROPERTY OF HAGER
COMPANIES. ANY REPRODUCTION
INPART OR AS A WHOLE WITHOUT
THE WRITTEN PERMISSION OF
HAGER COMPANIES IS PROHIBITED.
SHEET 1 OF 1
Q.A.
ENG. APPR.
DRAWN
TOLERANCES:
FRACTIONAL: 0.015"
ANGULAR: MACH: 1 BEND: 1
TWO PLACE DECIMAL: 0.01"
THREE PLACE DECIMAL: 0.004"
DO NOT SCALE DRAWING
FINISH
MATERIAL
REV.
A
DWG. NO.
SIZE
SCALE:1:4
HAGER RESERVES
THE RIGHT TO
MAKE DESIGN
CHANGES
WITHOUT NOTICE.
CALL HAGER
ENGINEERING AT
1-800-325-9995
FOR THE LATEST
REVISION DATE
OF TEMPLATE.
-
LATCH
THUMB TURN
ASSEMBLY
MOUNTING SCREWS
STRIKE
WOOD FRAME
REINFORCER
DUST BOX
BLANK MOUNTING
PLATE
Insert latch and tighten to the door
using #8 screws.
c.
IF INSTALLING A 3222 RETRO FIT KIT:
- Refer to Step 5 for installation
w/Blank Mounting Plate
3220 SHOWN
TEMPLATE
07/28/08
HAGER COMPANIES
139 Victor Street, St. Louis, MO 63104 (800) 325-9995 Fax (800) 782 0149
