background image

4500 Series Surface Vertical Rod Exit Device

Installation Instructions

Grade 1

I-ED00792

REV 3

Page 7 of 11

8. INSTALL TOP MOUNTING BRACKET

9. INSTALL TOP LATCH AND STRIKE

Remove top latch cover and mounting bracket from top latch assembly.  Fold and apply template to door using edge of door and face of top stop.  Mark and drill holes as shown on template for both top latch bracket and strike.  Be sure the vertical centerline for the top latch mounting holes is 2 7/16” from the edge of door.  Install top mounting bracket.

- For metal doors, drill and tap for 1/4”-20 machine screws. 
- For wood doors, pre-drill 1/8” holes.  
- ?For Sex Bolts, drill 5/16” clearance holes on exit device side (push side) and 3/8” on pull side.

Remove top latch cover and mounting bracket from top latch assembly.  

Fold and apply template to door using edge of door and face of top stop.  

Mark and drill holes as shown on template for both top latch bracket and 

strike.  Be sure the vertical centerline for the top latch mounting holes is 

2 7/16” from the edge of door.  Install top mounting bracket.

-For metal doors, drill and tap for 1/4”-20 machine screws. 

-For wood doors, pre-drill 1/8” holes.  

-For Sex Bolts, drill 5/16” clearance holes on exit device side (push side) 

and 3/8” on pull side.

A. 

Install top strike to face of 

 

stop using only the two 

 

outer slotted mounting 

 

holes.

B. 

Install top latch assembly 

 

to top mounting bracket 

 

using provided screw and 

 

top two slots in bracket.

C. 

Close door, check 

 

alignment of strike and top 

 

latch, adjust if required, 

 

and install screw into 

 

center hole in strike.  

2 7/16"

62

 

TO DOOR EDGE

(2-3/8" [60] TO FACE OF STOP)

3 1/4"

82

LATCH MOUNTING

BRACKET

2 29/32"

[74]

Screws:

Metal door/sex bolt -

1/4” - 20 machine screws (1)

Wood door -

#12 wood screws (1)

INSTALL AFTER

ALIGNMENT HAS

BEEN SET

MOUNTING

BRACKET

TOP LATCH

ASSEMBLY

1 29/32"

48

15/16"

24

19/32"

15

7/8"

22

2 7/16"

62

DOOR

FRAME SOFFIT

Strike Fasteners:

Metal stop -

1/4” - 20 flat head machine screw (3)

Wood stop -

#12 flat head wood screw (3)

26490169

Summary of Contents for 4500 Series












Reviews: