background image

OR-05/18/15

Smart Touch Controller Setup Guide

pg.9

Quality Water International 

®

Mode 1 - Timer Mode - Frequency

Mode 1 - Timer Mode - Days of Week

Mode 2 - Demand Delayed Mode

Mode 3 - Demand Immediate Mode

72 - 96 Hour Regeneration

Smart Touch Operating Modes

When the appliance is in Mode 1 - 

Frequency

, it will regenerate based on the frequency that is set.

For example every one day or up to every 20 days. The days between regenerations can be set in the “Service Settings”.

When Frequency is selected, the next 
screen will allow you to chose how 
many days between regenerations.

When Days of Week is selected, the 
regeneration days can be selected in 
the “Customer Settings”.

In “Customer Settings”, check the 
days in which you would like the unit 
to regenerate. “OK” to continue.

Enter the number of days (1-20) 
between regenerations.

When the appliance is in Mode 1 - 

Days of Week

, it will regenerate on a specific day(s) of the week.

When the appliance is in the Patented Savematic Demand Delayed mode, it will regenerate based on the actual water 
usage and the total capacity of the appliance. The time that the regeneration takes place can be set, for example 2:00 
AM. Should the total capacity be depleted before the set regeneration time, a forced regeneration will occur.

When the appliance is in the Demand Immediate mode, it will regenerate based on water usage alone. Regeneration will 
occur when the capacity limit is reached. The time of regeneration cannot be set.

If this value is set to Yes, the appliance will be forced to regenerate every 96 hours unless a regeneration based on water 
usage occurs within the time interval. The value should always be set to Yes if iron is present in the water.

The controller has a Timer mode (Mode 1 Frequency and Mode 1 Days of the Week), a Demand Delayed mode (Mode 
2), and a Demand Immediate mode (Mode 3). These modes are equipped with Capacity Guard

®

, which ensures that a 

supply of conditioned water will be available even with excessive water usage. 

Operating Modes

Summary of Contents for ST-200













Reviews: