background image

Page 12 

3)

 

Press the pushbutton on the HAI UPB™ 6-Button Room Controller five (5) times quickly. 

 

4)

 

Each UPB™ Wall Switch Dimmer will flash its lighting load one time to indicate that the new level has been configured. 

 
Whenever the scene command is transmitted, by pressing the Scene Button (A-D) on the Room Controller, each HLC device in the 
specified room will brighten or fade to its preset level for the selected scene. 
 
 

To set a lighting scene using the Lumina keypad: 

 

1)

 

Adjust all of the HLC devices in the room to the desired lighting levels.  The desired lighting levels may be set manually at 
the switch by pressing the top of the paddle to brighten the light or the bottom of the paddle to dim the light.   
 

 

 

2)

 

After the desired lighting levels are set, from the top-level display or from the main menu, press the 1 (CTRL) key on the 
Lumina keypad. 

 

3)

 

Lumina will display the first named unit in that list.  Use the down arrow key to scroll through the list.  Press the ' # ' key to 
select the desired room. 

 

4)

 

Press the 6 (SET) key followed by 1 (On Scene) or 2-5 (Scene A-D) to save the new “light levels” for each device in the 
selected room. 

 

Living Room SET

 

  1=ON 

2-5=A-D

 

 
Whenever the scene command is transmitted each HLC device in the specified room will brighten or fade to its preset level for the 
selected scene. 

 
 

Summary of Contents for lumina


























Reviews: