background image

Page 2 

INSTALLATION 

 

1)

 

Install HLC Switches and Controllers

 

 
Install the HLC Dimmers and Switches, 6-Button Room Controllers, and 8-Button House Controllers according to the instructions 
that came with each device.

 

 
2)

 

Install the HLC Phase Coupler

 

 
Install the supplied HLC Phase Coupler (P/N: 39A00-1) according to the instructions that came with the unit.

 

 
3)

 

Mount the Lumina Enclosure

 

 
Mount the Lumina enclosure securely to the wall in the selected location using screws and wall anchors, as appropriate. 

 

4)

 

Ground the Lumina Controller

 

 
GROUND THE LUMINA CONTROLLER’S "EARTH GND" TERMINAL TO A COLD WATER PIPE OR TO A 4-FOOT 
GROUND ROD TO PRESERVE ITS BUILT-IN TRANSIENT PROTECTION.  USE 14 GAUGE WIRE.  TRANSIENT 
PROTECTION WILL NOT WORK IF THE CONTROLLER IS NOT PROPERLY GROUNDED. 

 

ACCORDANCE WITH THE NATIONAL
ELECTRIC CODE, ANSI/NFPA 70.

COLD WATER PIPE
OR GROUND ROD

GOUNDING METHOD MUST BE IN

 

 
 

5)

 

Connect the Powerline Interface Module (PIM) to the Lumina 

 

Locate the supplied PIM (P/N: 36A00-1).  Plug the PIM into a 120 VAC outlet.  Plug one end of the supplied 6-conductor 
modular cable into the connector marked “J3” (SERIAL 3) on the Lumina controller and plug the other end into the modular 
connector on the PIM as shown. 
 
 

         

6 CONDUCTOR

<Program

Status

Powerline Interface Module

UPB™

 

 

 

Summary of Contents for lumina


























Reviews: