background image

147

MINI 4-way cassette 

type indoor unit

4.9.2 Safety

 

If the air conditioner is transferred to a new user, this manual shall be transferred to the user, together with the 

conditioner.

 

Before installation, be sure to read Safety Considerations in this manual for proper installation.

 

The safety considerations stated below is divided into " Warning" and "  Attention". The matters on severe 

accidents caused from wrong installation, which is likely to lead to death or serious injury, are listed in "

Warning". However, the matters listed in "  Attention" are also likely caused the severe accidents. In general, 

both of them are the important items related to the security, which should be strictly abided by.

 

After the installation, perform test run to make sure everything is in normal conditions, and then operate and 

maintain the air conditioner in accordance with the User Manual. The User Manual should be delivered to the 

user for proper keeping.

   WARNING

 

Please ask the special maintenance station for installation and repair. Water leakage, electric shocks or fire 

accidents might be caused from improper installation if you conduct the installation by your own.

 

The installation should be conducted properly according to this manual. Water leakage, electric shocks or fire 

accidents might be caused from improper installation.

 

Please make sure to install the air conditioner on the place where can bear the weight of the air conditioner. The 

air conditioner can't be installed on the grids such as the non-special metal burglar-proof net. The place with 

insufficient support strength might cause the dropdown of the machine, which may lead to personal injuries. 

 

The installation should be ensured against typhoons and earthquakes, etc. The installation unconformable to the 

requirements will lead to accidents due to the turnover of the machine.

 

Specific cables should be used for reliable connections of the wirings. Please fix the terminal connections reliably 

to avoid the outside force applied on the cables from being impressed on the cables. Improper connections and 

fixings might lead to such accidents as heating or fire accidents.

 

Correct shapes of wirings should be kept while the embossed shape is not allowed. The wirings should be reliably 

connected to avoid the cover and the plate of the electrical cabinet lapping the wiring. Improper installation might 

cause such accidents as heating or fire accidents.

 

While placing or reinstalling the air conditioner, except the specific refrigerant (R410A), don't let the air go into the 

refrigeration cycle system. The air in the refrigeration cycle system might lead to the cracking or personal injuries 

due to abnormal high pressure of the refrigeration cycle system.

 

During installation, please use the accompanied spare parts or specific parts. If not, water leakage, electric 

shocks, fire accidents or refrigerant leakage might be caused.

 

Don't drain the water from the drainpipe to the waterspout where may exist harmful gases such as sulfureted gas 

to avoid the harmful gases entering into the room.

 

During installation, if refrigerant leakage occurs, ventilation measures should be taken, for the refrigerant gas 

might generate harmful gases upon contacting the flame.

 

After installation, check if any refrigerant leakage exists. If the refrigerant gas leaks in the room, such things as air 

blowing heaters and stoves, etc. may generate harmful gases.

 

Don't install the air conditioner at the places where the flammable gases may leak. In case the gas leakage 

occurs around the machine, such accidents as fire disasters may be caused.

 

The drainpipe should be properly mounted according to this manual as to ensure the smooth drainage. In 

addition, heat preservation should be taken to avoid condensation. Improper drainpipe mounting might cause 

water leakage, which will get the articles at home wet.

 

The refrigerant gas pipe and liquid pipe should be heat insulated to preserve heat. For inappropriate heat 

insulation, the water caused from the condensation will drop to get the article at home wet.

Summary of Contents for AB052MCERA






























Reviews: