background image

13

PRECAUTION

Execute proper grounding. Do not connect the earth wire to a gas pipe, water pipe, lightening
rod, or a telephone ground wire. Improper placement of earth wires can result in electric shock.
An electric leakage breaker must be installed, otherwise electric shock or other accidents would
occur.
After completion of the installation,  the air conditioner shall be electrified to check for electric
leakage.

2. Preparation for installation

Installation tools

7     Pipe Cutter

14   Refrigeration Oil

6     Spanner

13   Scraper or File

5     Shifting Spanner

12   Measuring Tape

4     Inner Hexagon Spanner

11   Leakage Checker or Soap Liquid

3     60mm Drill

10   Clippers

2     Steel Saw

9     Knives

1     Screw Driver (flat  head,  wabbler,  triangle)

8     Pipe Expander

Instructions to installation

WARNING

Its improper installation can also result in heat generation or fire.
When setting up or moving the location of the air conditioner, do not mix air etc. or anything
other than the designated refrigerant within the refrigeration cycle.
Rupture and injury caused by abnormal high pressure can result from such mixing.
Always use accessory parts and authorized parts for installation construction. Using parts
not authorized by this company can result in water leakage, electric shock, fire and refrigerant
leakage.

CAUTION

Execute proper grounding. Do not connect the ground wire to a gas pipe, water pipe, lightning
rod or a telephone ground wire. Improper placement of ground wires can result in electric
shock.
The installation of an earth leakage breaker is necessary depending on the established
location of the unit. Not installing an earth leakage breaker may result in electric shock.
Do not install the unit where there is a concern about leakage of combustible gas.
The rare event of leaked gas collecting around the unit could result in an outbreak of fire.
For the drain pipe, follow the installation manual to insure that it allows proper drainage and
thermally insulate it to prevent condensation. Inadequate plumbing can result in water leakage
and water damage to interior items.

Summary of Contents for AD092XLERA





























Reviews: