background image

-------Internal training document for Haier service provider. External disclosure is prohibited --- Classification 

27 

27 

I

 -----------

 2nd-stage compressor                                           

J

-----------

 Evaporator   

12. Installation & Disassembly Process   

12.1 Installation Position 

12.1.1. Prevented from direct sunshine   

12.1.2. Good surrounding air ventilation condition 

12.1.3. Prevented from a lot of dust 

12.1.4. Prevented from mechanical vibration or shock 

12.1.5.  Ambient  temperature:  5

~28

;  maximum 

  32

;  the  most  ideal  temperature:  18

~25

the air-conditioning system shall be used if necessary.   

12.1.6. Working Position Height of the Equipment: Lower than 2000m.   

12.1.7. Working humidity: <80%RH. If the maximum working temperature is 32

, the humidity shall be 

lower than 57%RH.   

12.1.8. Input voltage: <220±10%.   

*Note:  Since  the  ULT  freezer  is  sensitive  to  the  ambient  temperature,  it  will  not  work  normally  if  its 
installation fails to meet the above requirements.   

Please use the equipment after improving the environment. 

12.1.9. Battery charging principle: There is a storage battery power switch on this equipment and this 
switch  shall  be  turned  on  before  the  freezer  is  switched  on.  As  long  as  the  switch  is  on,  the  AC 
equipment  which meets  the  relevant  requirement  will  work  normally. When AC  power  is  supplied,  the 
equipment will charge the storage battery according to the relevant requirement. If the AC power has a 
failure, the storage battery will supply power to the display panel for normal supply. When the storage 
battery charges to the voltage ≤10.5V, the battery will stop power supply and the display panel will not 
display.  Power  can  be  switched  off  thoroughly  and  the  display  panel  will  not  display  as  long  as  you 
disconnect  the  AC  power  line  and  then  switch  off  the  equipment  when  the  battery  can  supply  power 
normally.   

12.2 Product Carrying and Unpacking 

12.2.1  Carrying:  As  the  product  is  very  heavy,  a  forklift  or  pallet  jack  shall  be  used  for 
carrying it so as to avoid damages to people and the product.   

12.2.2  Unpacking:  The  product  package  composes  of  a  wooden  pallet  +  EPE  vertical 
column  winding  package  +  carton.  A  forklift  or  pallet  jack  shall  be  used  to  plug  into  the 
bottom of its pallet for carrying it.   

See the pictures below for its package. 

Summary of Contents for DW-86L338











































Reviews: