background image

– 23 –

To prevent the room from overheating (Zoneline 

must be powered), cooling is energized when 

the indoor temperature is sensed to be 85°F to 

maintain room temperature below 85°F in any 

operation mode except heating mode.  The 

Heat Sentinel mode is disabled when the room 

temperature reaches 80°F.  The indoor fan runs 

at high speed.  An auxiliary set mode is provided 

to enable the heat sentinel.  If the auxiliary mode 

is in the OFF position, the heat sentinel function 

is disabled.  The factory default of the mode is 

OFF.

To prevent the room from freezing, the electric 

heater is energized to maintain the room 

temperature above 41°F regardless of any 

operation mode. 

The freeze sentinel mode is disabled when the 

room temperature reaches 46°F. 

The indoor fan runs at high speed.  An auxiliary 

set mode is provided to enable the freeze 

sentinel.  If the auxiliary mode is in the OFF 

position, the freeze sentinel function is disabled.  

The factory default of the mode is ON.

The control panel can be locked out from the user 

being able to change the operating mode of the 

Zoneline.

While the Zoneline is operating in the desired 

mode, press and hold the “Display Show/Hide” 

button for 10 seconds to lock the control to this 

setting.

The display will then flash the mode LED and 

temperature that was locked five times and 

then go dormant.  Any key press after this will 

result in the mode LED and temperature to flash 

five times and then go dormant.  Pressing the 

“Display Show/Hide” button for 10 seconds will 

unlock the control and resume normal operation.

The Zoneline will come back on in the locked 

mode if power is lost and restored.

  Heat Sentinel Mode

  Freeze Sentinel Mode

  Control Lockout

  Auxiliary Controls

The red auxiliary set (or Aux Set) button is located 

behind the room cabinet, below the user interface.

There are ten different modes that can be set 

using the auxiliary set button.

To change modes, press the red auxiliary set 

button.  “AU” appears on the display.  Press the 

MODE button on the control until the first digit 

in the display shows the number corresponding 

to the desired mode being changed.  Press the 

up pad (+) or down pad (-) to make the HEAT or 

COOL selection where applicable.  Press the red 

auxiliary set (or Aux Set) button to confirm the 

selections once all changes have been made.

Summary of Contents for GE APPLIANCES AZ45E07DABW5




























































Reviews: