background image

– 21 –

  Reverse Cycle Defrosting Heat Pump Mode

Reverse Cycle Defrost shall be controlled as a 

function of compressor run time and outdoor coil 

temperature.

a) 

Defrost Enable

The reverse cycle defrost shall begin when 

either: 

1.  The outdoor coil temperature, as measured 

by the S4 thermistor during compressor 

operation is less than or equal to 14°F for 

at least 3 consecutive minutes.

-OR-

2.  The outdoor temperature as measured by  

the S3 Thermistor, is less than or equal 

to 42°F OR the outdoor coil temperature 

is less than or equal to 32°F for at least 3 

hours of accumulated compressor run time.

NOTE

: As described at step 1, if the outdoor 

coil temperature, as measured by the S4 

thermistor, rises above 14°F before 3 minutes 

has elapsed; the accumulated time register is 

reset to zero.  A defrost sequence will not be 

initiated, as a result.

NOTE

: As described in step 2, if the outdoor 

temperature, as measured by the S3 

thermistor, rises above 42°F AND the outdoor 

coil temperature as measured by the S4 

thermistor, rises above 42°F before 3 hours of 

compressor run time has been accumulated; 

the accumulated time register is reset to zero. 

A defrost sequence will not be initiated, as a 

result.

b) 

Defrost Operating Sequence

When either of these conditions are detected, 

the Zoneline will initiate a reverse cycle defrost.  

The following steps comprise the reverse cycle 

defrost: 

1.  Immediately stop heat pump operation.

2.  Run stage 3 heating until room 

temperature is satisfied.

3.  Wait for compressor off time (3 minutes) to 

be satisfied.

4.  Run reverse cycle defrost (cooling mode 

without fans) until either: 

•  the outdoor coil temperature rises to 68°F

•  or the total elapsed time of compressor run 

in reverse cycle defrost reaches 9 minutes

5.  Run a stage 3 heating cycle to satisfy room 

temperature.

6.  If reverse cycle defrost is exited due to

•  the outdoor coil rising above 68°F, resume 

normal heat pump operation

•  the total elapsed time exceeding 9 minutes 

and total number of defrost cycles is less 

than 5, go back to step 4 and run another 

defrost cycle.  If the total number of defrost 

cycles equals 5, see 

Abnormal Defrost 

Fault

 below

c) 

Abnormal Defrost Fault

If five consecutive defrost cycles have been 

completed and the outdoor coil has not 

reached 68°F, an Abnormal Defrost Fault will 

be initiated. Heat Pump operation is disabled 

while this fault is active.  The Zoneline will wait 

for the following conditions to be met.

1.  Elapsed time > 4.5 days

 and

2.  Outdoor Coil Thermistor > 42°F

 and

3.  Outdoor Ambient > 42°F

At this time, up to five more defrosts will be 

attempted.  If the outdoor coil thermistor stays 

below 68°F, it will reenter abnormal defrost 

fault.  If it increases above 68°F, it will resume 

normal heat pump operation.

Reverse cycle defrost has the highest priority.  

Once the defrost starts the defrost operation 

continues regardless of any temperature 

conditions and any kind of manual operation, 

except for changing the operation switch.

Reverse cycle defrost is used in Class 2 mode. 

During reverse cycle defrost, all Class 2 signal 

modes are overridden except when "Cooling" 

is called from the thermostat.

Summary of Contents for GE APPLIANCES AZ45E07DABW5




























































Reviews: