background image

Remove the transport packaging (fig.1)

 Remove the tape on the door (fig.2), the wall mounting kit and the inverted panel 

 film attached to the inside of the drum (fig.3)  before starting the dryer. 

Packing accessories

Check list of the accessories and materials provided with the machine:

To ensure the dryer operates normally, attention must be paid to the

following:
1. The rear of the dryer must not have any restriction to the intake of fresh 

    air. 

fig.1

fig.2

Dimensions

a=830 mm

b=600 mm

c=560 mm

Weight=30 kg

INSTALLATION INSTRUCTIONS

2. Check the dryer for any damage. If any damage is found do not operate 

    and contact your supplier or Authorised Service Centre.

3.The dryer must be kept away from flammable substances.

4.The surrounding environment must be dry and ventilated.

5. For best results

,

the ambient temperature should be between 10     

    and 35    .

8

fig.3

Name

Quantity

User manual                                     1

Wall mounting kit                              1

Inverted panel film                            1

Flexible hose                                    1

Flexible hose clip                             1

Hose connector                               1 

Unpacking your dryer

Stacking kit                                      1 

Summary of Contents for HDY-E60

















Reviews: