Universal Remote Control
EN-29
Haier LED HDTV
1.5 seconds. The code can not be saved to EEPROM.
Automatic Scan Programming the Controller
Y
To automatic scan program the Controller:
Manually turn OFF the device you wish to power scan.
A
(TV, VCR, DVD,STB, cable box or audio equipment).
Choose the device you wish to program.
B
While Press and holding ENTER key, press the INPUT
C
key and device LED will be ON. Keep the status for
about 3 seconds and the LED will blink, indicating
that the Controller is ready for programming, then
release both keys.
Press and release the Mute key to enter automatic
D
scan mode. And the remote will automatically
sending codes to the device per 2 seconds.
When the device turns ON, press
E
ENTER
key to
program the Controller with the new code, saving it
to EEPROM and exit.
Press
F
POWER
key, If the device responds, no further
programming is required. If the device does not
respond repeat steps 1 through 5.
After searching the entire data base, this mode will be
G
automatically exited and led will blink for 3 times. The
codeset is not saved to EEPROM.
In automatic scan mode, press any key other than
ENTER
key will exit without programming.
Display mode
Choose the device you wish to program.
A
To enter display mode, while press and holding
B
ENTER
key, press the
INPUT
key and device LED will
be ON, keep the status for about 3 seconds and the
LED will blink, indicating that the Controller is ready
for programming, then release both keys.
Sequence press 9, 8, 0 to enter display mode.
C
Press digit 1 key to get the first digit of current
D
codeset. For example, if the first digit of codeset is 1,
so then led will blink once and remains OFF. Digit “0”
in codeset will not be displayed. Blink Freq is 1 HZ.
Press digit 2 key to get the second digit of current
E
codeset. For example, if the second digit of codeset is
3, so then led will blink three times and remains OFF.
Blink Freq is 1 HZ.
Press digit 3 key to get the third digit of current
F
codeset. Blink Freq is 1 HZ.
Only digit 1, 2, 3 are valid in this mode. And the
G
sequence is not fixed.
Controller will not send out data in this mode if user
presses any keys other than digit 1, 2, 3, or no key was
pressed in 30 seconds, display mode is ended.
Punch-Through Features
The Controller provides two punch-through features
that allow users to control TV volume and DVD or VCR
operation while the Controller is in another device mode
control certain features of another device.
Volume Punch-Through
Y
The TV Volume/Mute punch-through feature allows
you to control the volume and mute function of your
TV while the Controller is in another device mode. The
feature is applicable for all devices and brands that do
not use the volume control buttons for other purposes.
Transport Key Punch-Through
Y
The DVD or VCR transport key punch through feature
lets you control the PLAY, STOP, PAUSE, REWIND, FF and
RECORD functions of your DVD or VCR while the Control
operates in other modes. The feature is applicable for all
devices and brands that do not use the transport keys
for other purposes.
Fast Programming Haier default TV codeset
Press and holding the
ENTER
key and then press
POWER
key for 3 seconds, the LED will blink 3 times and turn off,
default Haier codeset (001) will be programmed to the
control.
Remote Control Codes
TV
NO. Brand
Code
1
Haier
001 002 003 004 005 006 007 008 009 010 240 241 297 307 355
2
Abex
077
3
Acer
267
4
Addison
333
5
Admiral
057 078 334 338
6
Advent
324
7
Adventura
079
8
Aiko
066 333
9
Aiwa
165
10
Akai
038 058 258 271 279 331 350
11
Albatron
321 325
12
Alleron
068
13
America Action
335
14
Ampro
323
15
Amtron
067
16
Anam
335
17
Anam National
059 067
18
AOC
060 061 062 222 331 349 350 353
19
Apex
092 135 151 195 339
Summary of Contents for HL32XSL2a
Page 39: ...Warranty Haier LED HDTV EN 38 ...
