background image

Page

16

Error Display and Troubleshooting

Error message:Door is not properly shut 20s after program is started.

Troubleshooting:

N

Pushing the door to Check Whether Door
is properly shut or not

Y

Error message:Drainage error, water not emptied within 4 min.

Troubleshooting:

Y

Cut off the power and then turn on again.
Check the voltage between brown wire and
blue wire of door lock, is it between AC
220-240V?

N

Door

lock

is

broken

and

need

replacing, then make sure wire is

connected properly.

N

Check the voltage between brown wire
and blue wire of PCB, is it between AC
220-240V?

Check if drain pump acts by touching

pump position

Y

Check if drain pump or
drain pipe is jammed, and
open the filter and clean

N

Cut off the power and choose spin program to
start, then check the import voltage of drain
pump, is it between AC 220-240V?

Replace drain pump

N

Cut off power and pull out water level
pressure switch wire connection. Set spin
program to start. Check the export voltage to
drain pump, is it between AC 220-240V?

Replace PCB

Y

Replace

PCB

Connect

the wire

properly

Check if the wire connecting door lock

and PCB is loose

N

Check if water is emptied

Y

Cut off power and water level pressure switch wire
connection, measure the resistance of 1 and 3 pin, is it
infinite? If not, it is water level pressure switch failure
and replace it. If it is, then repair and check PCB and
wire as followed.

N

N

Y

Y

The wire between

PCB and drain
pump is not
connected
properly.
Replace the wire.

220-240v

Shut the door properly.

220-240v

Front Load Washing Machine

Model:

HNS1260TVE/ME

Summary of Contents for HNS1260TVE




























Reviews: