background image

Service Manual

Model No:HW60-1281S/1081

Issue
Rev.

1

General Information

Chapter1

General Guidelines

1.1

When servicing, observe the original lead dress. If a short circuitis found, replace all parts 
which  are  overheated  or  damaged  by  the  short  circuit. After  servicing,  see  to  it  that  all 
the  protective  devices  such  as  insulation  barriers,  insulation  papers  shields  are  properly 

 

that the screws, parts and wiring which were removed in order to service 

are put  in the original positions,  or whether there are the portions which are deteriorated 
around the service places serviced or not. And be sure safety of that.

Caution and Warning symbols 

1.2

We have provided many important safety messages in this manual. Always read and obey 
all safety messages.

This is the Safety Alert Symbol. This symbol alerts you to potential hazards that can 

kill or injure you and others. any instructions in this manual with the symbol must 
be followed strictly.

To prevent damage  to the  washing machine, any instructions in this manual with 

the symbol must be followed strictly.

Function indication symbols

1.3

Signify the washing machine has this function.

Signify the washing machine doesn't have this function.

Features Of The Unit

Chapter2

Convenient Door

2.1

The  unit  has  a  larger  transparent  door  that  you  can  observe  the  process  of  washing 
conveniently, and you can put clothes in the washer or take them out conveniently.

Optional Spin Speed

2.2

you can select different spin speed according to corresponding material of the clothes.

Unique Gasket Design

2.3

The  unit  can  left  little  water  in  the  gasket  after  the  process  of  washing  with  the  unique 
gasket.

Adjustive Delay Time

2.4

According to different conditions, you can select delay time from 1h to 24h.

Chapter3

Summary of Contents for HW60-1081






















Reviews: