18
To unlock press the "
"
and
case of abrupt power failure or the need to cut o
power
resume when the power is on again.
program selector again to choose another
program.
During the spin process, if too much foam is inspected, in order to protect the motor, the
Maintenance
.
l
e
n
n
o
s
r
e
p
e
c
n
a
n
e
t
n
i
a
m
e
h
t
t
c
a
t
n
o
C
.
l
e
n
n
o
s
r
e
p
e
c
n
a
n
e
t
n
i
a
m
e
h
t
t
c
a
t
n
o
C
Water level sensor error.
ror
r
E
r
o
t
o
M
F7
E8
FA
FC1
FC2
Contact the maintenance personnel.
UNb
Washing machine has an unbalanced load
weight is greater than allowable maximum,
the washing machine will not spin and will
and noise
End
1:25
19:30
End of wash cycle.
1.In case washing 1 piece of laundry(carpet,
bed sheet,table sheet,ect) make it
symmetrical inside the drum.
2.Lower the wet weight of laundry pieces
by wringing manually and placing them
piesces inside the washing machine in a
ofr the drum.
4.Add 1 or 2 pieces of laundry into the durm
to reduce the unbalanced load
eff
ects.
5.Restart the spin cycle by cloosing spin
programme.In case the failure persists,
please ask a quali
fi
ed technician to repair it.
.
l
e
n
n
o
s
r
e
p
e
c
n
a
n
e
t
n
i
a
m
e
h
t
t
c
a
t
n
o
C
.
l
e
n
n
o
s
r
e
p
e
c
n
a
n
e
t
n
i
a
m
e
h
t
t
c
a
t
n
o
C
Temp.
Temp.
Intense
Intense
board and motor
board and power board
6.Select a lower spin speed, and if OK then
select Spin program and a higher spin speed.
knobs.
19
Trouble-Sho
Problem
Causes
Solu ons
Trouble-Shoo ng
Power failure.
The washer door is not properly closed.
Machine has not been switched on.
Check the power supply.
Close the washer door properly.
Make sure the machine is switched on.
Water tap is not turned on.
Water pressure is less than 0,03 MPa.
The inlet hose is kinked.
Water supply failure.
The program knob is not properly set.
The washer door is not properly closed.
ter is blocked.
P
Turn on the water tap.
Check water pressure.
Check the inlet hose.
Ensure the water supply.
Set the program knob properly.
Close the washer door properly.
ter.
The height of the drain hose is below
80 cm.
The drain hose is in water.
Drain hose is blocked.
Drain hose end is higher than 100 cm
above
vel.
ter is blocked.
removed.
Washing machine is located on an uneven
surfaceor is not level.
Machine load is over 7/8/10kg.
Water or electricity failure.
Install drain hose within 80-100 cm
of height.
Make sure the drain hose is not in
water.
Unblock the drain hose.
Make sure the drain hose end is lower
than 100 cm abov
vel.
ter.
Make sure the washing machine is on
an even surface and levelled.
Reduce amount of laundry in the
drum.
Check the power supply or water
supply.
Washing machine gives an error message.
Washing machine is in soaking cycle?
The detergent is not a low-foaming type or
for manual wash.
Excessive use of detergent.
adjusted
Unbalance of the laundry
Check display codes.
Check if your detergent is appropriate.
Reduce amount of detergent in the
This is normal and doesn't a ect the
Add clothes or run a spinning
program again.
Washing machine fails to operate.
Washing machine c
with water.
Machine is draining while being
Drainage failure.
wash cycle.
Excessive foam in the drum, which is
Spinning fails
