background image

Safety precautions

Please insert the power cord into
special receptacle with rated vol-
tage.Be sure to use single-phase
 three pins  receptacle.The earthing
 terminal of the receptacle must be
 earthed reliably.If possible,please
adopt electric leakage protector.

When the machine is normally
using, please put  the power plug
at the location easily to be insert-
ed and extracted by hand. Be sure
to pull the plug off when there's
power failure, or the machine is
being moved, cleaned orwhen it
is idle.

If  the power cord is bad, to avoid risk it is required to replace it by the 
technicians ofour special shop or the after-sale service department.
Keep the pin of the power plug clean.

Do  not  put  the  machine  at  damp
place like  the  bathroom .  Never
wash  it   with water. Do not place 
wet laundries on the control panel.

Do not use water hotter than 50 C .

In case the washing  machine is  installed
on  ground  with  carpet ,  do not block the 
ventilation  hole  with  carpet.

Ventilation hole at
the bottom of the
washing machine

Do not wash water-proof laundries like
the raincoat,  bike  covers etc. to avoid 
abnormal vibrations  in spinning.

Do not let the machine share one receptacle
with  other electric  appliances. If  the  power
plug  is  damaged,  or  the  plugging  into the
receptacle  is loose, do not use the plug any
more.

2

Summary of Contents for HWM72-27S



















Reviews: