background image

2

Safety precautions

Please insert the power cord into special
receptacle with rated voltage. Be sure to
use single-phase three pins receptacle.
The earthing terminal of the receptacle
 must be earthed reliably. If possible,
please adopt electric leakage protector.

When the machine is normally using,
please put  the power plug at the 
location easily to be inserted and
extracted by hand. Be sure to pull the
plug off when there's power failure, or
the machine is being moved, cleaned
or when it is idle.

Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.
Keep the pin of the power plug clean, if the power plug is polluted with dust,
please wipe with dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is required to have

it replaced by the technicians of our special shop or the after-sale service
department.

Do  not  put  the  machine  at  damp
place like  the  bathroom .  Never  wash 
it   with water. Do not place wet laundries
on the control panel.

Do not use water hotter than 50 C .

In case the washing  machine is  installed
on  ground  with  carpet ,  do not block the
ventilation  hole  with  carpet.

Ventilation hole at
the bottom of the
washing machine

Do not wash water-proof laundries like
the raincoat,  bike  covers etc, to avoid 
abnormal vibrations  in spinning.

Do not let the machine share one receptacle
with  other electric  appliances. If  the  power
plug  is  damaged,  or the  plugging  into the
receptacle  is loose, do not use the plug any
more.

Summary of Contents for HWM80-0626S




















Reviews: