49-55125-1
5
ENGLISH
USING THE DISHWASHER
Features and appearance will vary throughout this manual
SELECT CYCLE
Open the door and press the
Cycle Select
pad for the desired wash cycle. The light next to the
Cycle Select
pad will be
lit to indicate which wash cycle has been selected.
NOTE:
Cycle times vary based on soil level, water temperature, and options selected.
The cycle must be selected with the door in the open position. The cycle will not start until the
Start
pad is pushed and
the door is closed within 4 seconds.
AutoSense
This cycle automatically senses the soil level and adjusts the wash cycle accordingly. It is meant for daily,
regular, or typical use to completely wash a full load of normally soiled dishes and is designed to conserve
both water and energy.
NOTE:
AutoSense
was used to rate the energy efficiency of this dishwasher.
Heavy
This cycle is meant for heavily soiled dishes, cookware, pots, or pans with dried-on or baked-on soils.
Everyday dishes are safe to be used in this cycle.
Light
This cycle is for lightly soiled dishes. It is safe for china and crystal with no options selected.
4
LOAD DISHWASHER
For best dishwashing results, follow the loading guidelines found in the
Loading
section. No pre-rinsing of normal food
soil is required. Scrape off hard soils, including bones, toothpicks, skins, and seeds. Remove leafy vegetables, meat
trimmings, and excessive amounts of grease or oil.
ADD DETERGENT
Add needed amount of detergent to the detergent dispenser. Use detergent such as
Finish
®
Quantum
®
Automatic
Dishwashing Detergent
. See
Dispensers
section.
ADD RINSE AGENT
Add rinse agent such as
Finish
®
Jet-Dry
®
Rinse Aid
to the rinse agent dispenser. See
Dispensers
section.
NOTE:
The
use of rinse aid can further enhance the dishwasher’s drying performance.
1
2
3
SELECT OPTIONS
Wash
Temp
Allows you to select a higher wash temperature. These options are only available for
Heavy
and
AutoSense
cycles. Press the
Wash Temp
pad until the light next to the desired option comes on.
Boost
This option raises the water temperature and extends the cycle time in order to achieve better wash
performance.
Sanitize
This option raises the water temperature in the final rinse to sanitize your dishware. The cycle length may vary
depending on the temperature of your inlet water.
NOTE:
Cycles using this option are monitored for sanitization requirements. If the cycle is interrupted
during or after the main wash portion or if the incoming water temperature is so low that adequate water
heating cannot be achieved, the sanitizing conditions may not be met. In these cases, the Sanitized
light will not illuminate at the end of the cycle. Utilizing this option will modify the cycle to meet the
requirements of Section 6, NSF 184 for soil removal and sanitization efficacy.
NOTE:
NSF certified residential dishwashers are not intended for licensed food establishments.
Delay Start
This option allows you to delay the start of a wash cycle for up to 12 hours. With the door open and a
cycle selected, press the
Delay Start
pad to choose the number of hours you want to delay the start of
the wash cycle. The hours will show in the display window.
NOTE:
You may cancel the
Delay Start
timer by holding the
Start
pad for 3 seconds. This will also cancel
the wash cycle.
Control
Lock
You can lock the controls to prevent selections from being made. You can also lock the controls after
you have started a cycle to prevent cycle changes. For example, children cannot accidentally start the
dishwasher by pressing pads with this option selected.
To LOCK/UNLOCK the dishwasher control,
press and hold the
Cycle Select
and
Wash Temp
pads for 3
seconds. The lock control light ( ) will turn on to indicate the control is locked and will turn off to indicate
the control is unlocked.
5
Sanitized
Clean
Cycle
Select
Wash
Temp
Delay
Start
AutoSense
Heavy
Light
Boost
Sanitize
1-12 hrs
Start
Hold 3 Sec
Hold 3 Sec To Cancel
