Haier QPHR50LZ, Owner'S Manual And Installation Instructions

49-5000429   Rev. 4

5

ENGLISH  

CONTROLS

Other Features

Controls

NOTE:  When the bucket is full or removed, the controls cannot be set.
1.  Power Pad

Press to turn the dehumidifier on and off. 

NOTE: Turning off the power by pressing the Power button does 

NOT disconnect the appliance from power supply.

"ÏäñÜóèèçÙäç

Controls the fan speed.
Press to select either High, Medium, Low, or Smart Dry fan speed.
Set the fan control to High for maximum moisture removal. When 

the humidity has been reduced and quiet operation is preferred, 

set the fan control to Medium or Low. Smart Dry compares the set 

humidity level with the actual humidity and adjusts the fan speed 

automatically.

3.   Display

Shows the set % humidity level while setting, then shows the 

actual (+/– 5% accuracy) room % humidity level.

$Ñøðìçì÷üÜè÷Ìòñ÷õòïÙäçö

Ýëèëøðìçì÷üïèùèïæäñåèöè÷úì÷ëìñäõäñêèòé#%]ÛѤÛèïä÷ìùè
Ñøðìçì÷ü¥÷ò( ]ÛѤÛèïä÷ìùèÑøðìçì÷ü¥ìñ%]ìñæõèðèñ÷öòõ
in Nonstop mode for continuous operation.  To set the unit for 
continuous operation, press the   pad until the “Nonstop” 
indicator light is illuminated.
NOTE:  If Nonstop is selected, the dehumidifier will operate 
continuously at its maximum dehumidification settings if attached 
to a hose to drain or until the bucket is full. For drier air, press the 

  pad and set to a lower percent value (%). For damper air, press 

the   pad and set to a higher percent value (%). When you first use 
the dehumidifier, set the humidity control to 45% or 50%. Allow at 
least 24 hours for the dehumidifier to achieve the humidity level. 
If you still have damper air than desired, set the humidity level to a 
lower setting or select Nonstop for maximum dehumidification.

5.  Filter Timer

After 250 hours of operation, the Clean the Filter indicator light will 

glow to remind you to clean the filter. Remove the filter and clean it. 
Press and hold Filter button for 3 seconds to reset the filter 

reminder. See the Care and Cleaning section.

6.  Delay Off

While the dehumidifier is operating press the Delay button.
Press the   /   buttons to select the number of hours you want 

the dehumidifier to continue to operate before turning Off.
NOTE: After displaying the time, the Display will revert to showing 

the current humidity after 5 seconds have passed. Pressing the 

Delay button will display the number of hours left on the delay.
Delay On
While the dehumidifier is off press the Delay button.
Press the    /    buttons to select the number of hours you want 

the dehumidifier to remain off before turning On.
NOTE: The display will show the number of hours left until the 

dehumidifier turns on.
To cancel the Delay:
Press the Delay button once, the hours remaining on the Delay will 

appear on the display. Press the Delay button again and the Delay 

will be cancelled.

7. Pump

Activates the internal pump function. Press for 3 seconds to 

activate the internal pump for automatic removal of  condensate. 

The internal pump indicator light will remain illuminated after 3 

seconds. Press to deactivate the pump. Before turning on the 

pump, ensure the hose is connected.

8. Empty Indicator

The “Empty” indicator will blink when the bucket is ready to be 

emptied, or when the bucket is removed and/or not replaced in the 

proper position.

Alarm
If the bucket is full or missing, an alarm will sound for about 10 

seconds to remind you to empty and replace the bucket.
Auto Shut Off
The Water Level Control Switch shuts off the dehumidifier when the 

bucket is full, or when the bucket is removed and/or not replaced 

in the proper position. An alarm will sound if the water level control 

switch is not reset.

NOTE:  The fan and compressor will stop running as soon as the

bucket is removed.
Auto Defrost
When frost builds up on the evaporator coils, the compressor will 

cycle off and the fan will continue to run until the frost disappears.
Power Outage
In the case of a power outage or interruption, the unit will automatically 

restart, in the settings last used, after the power is restored.

Appearance may vary by model.

Humidity %

Hold 3 Sec

Requires Hose