background image

11

12

Selecting Simulation Mode

When you select Simulation Mode, you will enter Simulation Mode with the Simulation Mode Standby

screen shown. If the HAKKO FU-500 receives a Start signal when this screen is displayed, 

it will behave in the same manner as in Auto Mode but the motor will not start (no solder will be fed). 

Note that no solder feed or iron control error will be detected.

Simulation Mode

Standby

Start signal

received

Simulation Mode

PS 00

Primary Feed

Selecting Test Operation Mode

When you select Test Operation Mode, you will enter Test Operation Mode. 

In this mode, the HAKKO FU-500 will start to operate in PS (point soldering) mode for operation check

or adjustment after selecting a program number.

The HAKKO FU-500 outputs the same signal to the robot as the output signal in Auto Mode. 

All input signals from the robot will be ignored, but any solder feed error will be detected

and displayed. 

Test Operation

Test Operation

PS 00

Primary Feed

Select

program No.

START

Operation completed

Select SET PRG NUM

※ Tens place -> Units place -> Confirm

Selecting Auto Mode

When you select Auto Mode, you will return to the Auto Mode Standby screen. 

If the HAKKO FU-500 receives a Start signal when this screen is displayed,

it will start to operate for Auto Mode.

Auto Mode

Standby

Start signal

received

Auto Mode

PS 00

Primary Feed

Turn on the power switch of HAKKO FU-500. 

The start-up screen will be displayed, and then move to Auto Mode Standby screen. 

If the HAKKO FU-500 receives a Start signal when this screen is displayed, it will start to operate

for Auto Mode. 

If the HAKKO FU-500 does not receive a Start signal and the control button is pressed,

it will show the Mode Select screen.

To change the value or the cursor position, turn the control knob and then press the knob to confirm. 

Auto Mode

Standby

Control

button

Mode Select

Changing the settings

(3 lines are displayed at a time.)

Auto Mode

SimulationMode

Test Operation

Solder Feed

Program Set

Parameter Set

Log View

Select

Program Number

0

 

0

START

SET PRG NUM

Exit

FEEDER CONTROLLER

3) Uploading the HAKKO FU-601 tip temperature

The PC I/F reads in the iron tip temperature from the HAKKO FU-601 and uploads it to the PC.

4) Uploading the operation log

The PC I/F uploads the total number of soldering points and the total amount of fed solder to the PC.

5) Clearing the operation log.

The PC I/F clears the operation log.

The PC I/F does not operate while the feeder is run except for uploading of the tip temperature. 

The display for uploading of the tip temperature is not updated while the feeder is run.

For more information about how to use, see the HAKKO FU-500 PC Link Software Instruction Manual. 

The PC Link Software can be downloaded from the HAKKO Document Portal after user registration.

FU-500

ESD

SAFE

Summary of Contents for FU500-71X

























Reviews: