5. OPERATION
・When DSP (Display) is pressed
The selected information will be displayed on the screen.
SHOW PROFILE
The set profile information (Station, User, and Solder) is displayed.
SHOW TIP LOADS
The soldering count is displayed. By selecting RESET and then OK, the count is reset to 0.
To escape without resetting, select CANCEL.
SHOW TIP TIME
The cumulative running time on the iron tip is displayed. * Not including shut-off period. By selecting RESET
and then OK, the period is reset to 0. To escape without resetting, select CANCEL.
SELECT PROFILE
The profile information to be displayed is selected here. Profile information No.1 or No.2 can be selected.
▲
ＳＨＯＷ ＰＲＯＦＩＬＥ
ＳＨＯＷ ＴＩＰ ＬＯＡＤＳ
ＳＨＯＷ ＴＩＰ ＴＩＭＥ
＜↑＞ ＜↓＞ ＜ＯＫ＞
The cursor moves by pressing the <
↑
> or <
↓
>
button. The following items are displayed in order.
・ＳＨＯＷ ＰＲＯＦＩＬＥ
・ＳＨＯＷ ＴＩＰ ＬＯＡＤＳ
・ＳＨＯＷ ＴＩＰ ＴＩＭＥ
・ＳＥＬＥＣＴ ＰＲＯＦＩＬＥ
・ＴＩＰ ＴＹＰＥ
・＜ＣＡＮＣＥＬ＞
ＰＥＯＦＩＬＥ １
ＳＴＡＴＩＯＮ ＩＤ
ＵＳＥＲ ＮＡＭＥ
ＳＯＬＤＥＲ ＴＹＰＥ
ＰＥＯＦＩＬＥ １
Ｓ：○○○○○
Ｕ：××××××
Ｓ：△△△△
ＴＩＰ ＬＯＡＤＳ
ａｐｐｒｏｘ．
ｘｘｘｘｘｘ ｐｏｉｎｔｓ
＜ＲＥＳＥＴ＞ ＜ＯＫ＞
Ｒｅａｌｌｙ ＲＥＳＥＴ ＯＫ？
＜ＣＡＮＣＥＬ＞ ＜ＯＫ＞
When RESET is selected
Ｒｅａｌｌｙ ＲＥＳＥＴ ＯＫ？
＜ＣＡＮＣＥＬ＞ ＜ＯＫ＞
When RESET is selected
ＴＩＰ ＴＩＭＥ
ｘｘｘｘ ｈｏｕｒｓ
＜ＲＥＳＥＴ＞ ＜ＯＫ＞
１ｘｘｘｘｘｘｘ
２ｚｚｚｚｚｚｚｚ
＜１＞ ＜２＞
NOTE:
If you select RESET in the TIP LOADS screen or the TIP TIME screen, you need to enter
the password if password lock is set.
NOTE:
If any user name is set, it is displayed
in this step.
CAUTION
The solder count is an approximate number. The number is sometimes counted when
temperature change occurs in the tip other than soldering.
