1. Contents and Part Names
Confirm the contents before use.
Cleaning wire
Iron cover
Plug
Iron receptacle
Iron holder
Component bed
Cleaning brush
Cleaning
sponge
Options
Sold separately
Tip (a set of 2)
Confirm the tip/replacement parts/options on the website.
https://www.hakko.com/
2.
Specifications
This product cannot be used on its own.
Applied tip
400ºC (750ºF) : T38-02 Series
350ºC (660ºF) : T38-03 Series Heater
IH (High-Frequency
Induction Heating)
Applied
station
HAKKO IH soldering iron
(Confirm details on the
website.)
Cord length 1.3 m (4.3 ft)
Total length 130 mm (5.1 in) (If the
I type tip is attached)
Tip to ground
resistance
<2 Ω
Weight
32 g (0.07 lb) (If the
I type tip is attached)
Tip to ground
potential
<2 mV
* The total length and weight excludes the cord.
* This product is applied with electrostatic countermeasures.
* Please note that specifications and appearance are subject to change without notice in
the interest of product improvement.
CAUTION
■
Handling precautions for ESD Safe products
This product contains electrostatic countermeasures, so please use the following precautions.
1. Not all plastic parts are insulators, they may be conductive. Be careful not to expose live
electrical parts or damage insulating materials when performing repairs or replacing parts.
2. Be sure to ground the product before use.
※
各言語（日本語、英語、中国語、フランス語、ドイツ語、韓国語）の取扱説明書は以
下の
URL
、
HAKKO Document Portal
からダウンロードしてご覧いただけます。
（商品によっては設定の無い言語がありますが、ご了承ください。）
*
各國語言（日語、英語、中文、法語、德語、韓語）的使用説明書可以通過以下网站的
HAKKO Document Portal
下載參閲。
（有一部分的產品沒有設定外語對應、請見諒）
* Instruction manual in the language of Japanese, English, Chinese, French, German,
and Korean can be downloaded from the HAKKO Document Portal.
(Please note that some languages may not be available depending on the product.)
https://doc.hakko.com
3. Warnings, Cautions, and Notes
Warnings, cautions, and notes are placed at critical points in this manual
to direct your attention to significant items. They are defined as follows:
WARNING: Failure to comply with a WARNING may result in serious
injury or death.
CAUTION
: Failure to comply with a CAUTION may result in injury to the
operator, or damage to the items involved.
NOTE: This indicates procedures or information that are important
in a process described in this document.
Be sure to observe the following precautions to ensure safety.
WARNING
●
Those without the permission of a manager and those
without the required experience or knowledge (includ-
ing children) are not allowed to use this product.
●
Do not allow children to play with this product.
●
Do not allow children to clean or perform user
maintenance without supervision.
●
When this product is not used, place the hand-
piece on the iron holder.
●
The tip reaches high temperatures when the
power source is turned on. You may risk getting
burned or causing a fire if mishandled.
Failure to observe the following precautions to ensure safety might result
in electric shock, malfunction or other trouble.
CAUTION
●
Before using this product, fully read all descriptions in this document.
●
When connecting the handpiece to the station, do so after turning
the power switch OFF. The station may become damaged.
●
When replacing parts, use only genuine HAKKO parts.
●
Do not modify this product.
●
Do not use this product with damaged cords or plugs.
Also, if this product is dropped or is damaged in other ways, immedi-
ately stop use of this product.
●
When inserting and removing the cord, hold the plug body and do
not pull the cord.
●
Do not allow this product to get wet. Also, do not handle it with wet hands.
●
Do not perform any other actions that may be considered dangerous.
4. Assembly
(1) Align the tip with the ▲ mark of the angle adjustment wheel and insert
the tip all the way.
Angle adjustment wheel
State where it is inserted all the way
D cut portion
Tip
▲ mark
▲ mark
(2) Place the handpiece on the iron holder.
Tip storing pocket
(4 spots)
Handpiece FX-1003......................
1
Iron holder FH-800 .......................
1
Cleaning sponge...........................
1
Cleaning wire ................................
1
Instruction Manual (this document) ....
1
MICRO TWEEZERS
FX-1003
Instruction Manual
Thank you for purchasing the FX-1003.
This product is a micro tweezers handpiece that
connects to the HAKKO IH station.
Before using this product, be sure to read this manual.
Keep this manual readily accessible for reference.
取説 FX-1003_EN_210301.indd 1
取説 FX-1003_EN_210301.indd 1
2021/03/01 13:19:52
2021/03/01 13:19:52
