Æ
UP
DOW
N
1
2
1
FX-95
2
2
Control card
HAKKO FX-952
Soldering station
Heat resistant pad
Iron holder
Power cord
Tip (not included)
HAKKO FM-2025
Insert the plug into
the receptacle until
it seats.
To disconnect, pull the plug
from the receptacle whilst
pressing down the tub on
the plug.
Receptacle
FM
-20
25
24
V-
70
W
Press the or button.
Press the button once.
Insert the card.
1
1
UP
DOWN
2
2
FX-952
Display for IRON 1 or 2
IRON 2 Heater
lamp
IRON 1
Heater lamp
Press the or button.
Press the button once.
Press the button once.
Sleeve assembly
NOTE:
Temperature setting can be changed even during
the display for the temperature and the heat to
the iron is OFF, If HAKKO FM-2025 soldering iron
and tip are connected properly.
®
Instruction Manual
1. PACKING LIST AND PART NAMES
2. SPECIFICATIONS
3. WARNINGS, CAUTIONS AND NOTES
4. INITIAL SETUP
Power consumption
Temperature range
Temperature stability
140W
200 - 450
°
C (400~840
°
F)
±
5
°
C (
±
9
°
F)
Output
Dimensions
Weight
24V
113 (W)
×
106 (H)
×
206 (D) mm
2.6kg
Please check to make sure that all items listed
below are included in the package.
Warnings, cautions and notes are placed at critical points in this manual to direct the operator’s
attention to significant items. They are defined as follows:
WARNING
l
Station
Power consumption
Tip to ground resistance
Tip to ground potential
Length of cord
Length, less cord
Weight, less cord
70 W (24 V)
< 2
Ω
< 2 mV
1.2 m (4 ft.)
188 mm (7.4 in.) with 2.4D tip
30 g (0.07 lb.) 2.4D tip
l
HAKKO FM-2025 soldering iron
NOTE:
The temperature were measured using the HAKKO 191
thermometer.
This product is protected against electrostatic discharge.
Specifications and design are subject to change without
notice.
A. Iron holder
l
The sponge is compressed. It will swell when mois-
tened with water. Before using the unit, dampen the
sponge with water and squeeze it dry.
B. Handpiece cord assembly
Pass the iron cord through the hole in the heat
resistant pad.
C. Soldering station
CAUTION
Be sure the power switch is OFF before connect-
ing or disconnecting the soldering iron cord. Fail-
ure to do so may result in damage to the circuit
board.
1. Insert the power cord into the receptacle at the
back of the station.
Insert the soldering iron cord into the receptacle
at the front of the station.
2. Set the iron in the iron holder.
3. Plug the power cord into a grounded wall socket.
CAUTION
The HAKKO FX-952 is protected against electro-
static discharge and must be grounded for full ef-
ficiency.
CAUTION
Using the sponge without dampen with water
may damage the tips.
CAUTION
Remove power and iron cords by holding the
plug-not the wires.
l
Changing the temperature setting
The allowable changes for temperature setting are:
°
C..........200~450
°
C
°
F...........400~840
°
F
Example: 350
°
C to 400
°
C for IRON 1
1. Confirm that the display of IRON is .
If it shows , press button to show .
2. Insert the control card into the slot in the
front of the unit.
• The hundreds digit will begin to flash, indicating
that the unit is in the TEMPERATURE SET
mode and data may be entered.
3. Entering the hundreds digit
• Press the or button to set the desired fig-
ure. When the desired figure is displayed, press
the button to enter. The tens digit will begin to
flash.
4. Entering the tens digit
• Press the or button to set the desired fig-
ure. When the desired figure is displayed, press
the button to enter. The units digit will begin
to flash.
5. Entering the units digit
• Press the or button to set the desired fig-
ure. When the desired figure is displayed, press
the button to enter. The desired temperature
is now entered into the system memory and
heater control will begin.
NOTE:
If power is switched off or lost during the execu-
tion of this procedure, no data will be entered. The
entire procedure must be repeated from step 1.
When you need one soldering iron only, refer to the
following example.
(Ex.)
IRON 2 is not required
1. Change the display of IRON to
2. Press button until the displayed figure disap-
pears.
NOTE:
The heat to the IRON 2 will not function.
3. Press button to display IRON 1.
The change is stored in the system memory and
does not disappear even after power off.
HAKKO FX-952 soldering station
1
HAKKO FM-2025 soldering iron
2
Control card
1
Power cord
1
Heat resistant pad
1
Iron holder
1
Instruction manual
1
HAKKO FX-952 soldering station
High-output, temperature controlled soldering station
WARNING:
Failure to comply with a WARNING may result in serious injury or death.
CAUTION :
Failure to comply with a CAUTION may result in injury to the operator, or damage to the
items involved. Two examples are given below.
CAUTION
When power is ON, tip temperatures will be between 200 and 450
°
C. (392 to 840
°
F.) To avoid injury or
damage to personnel and items in the work area, observe the following:
Do not touch the tip or the metal parts near the tip.
Do not allow the tip to come close to, or touch, flammable materials.
Inform others in the area that the unit is hot and should not be touched.
Turn the power off when not in use, or left unattended.
Turn the power off when changing parts or storing the HAKKO FX-952.
To prevent accidents or damage to the HAKKO FX-952, be sure to observe the following:
Do not use the HAKKO FX-952 for applications other than soldering.
Do not allow the HAKKO FX-952 to become wet, or use it when hands are wet.
Do not modify the HAKKO FX-952.
Use only genuine HAKKO replacement parts.
Do not bend or damage the control card. If the card does become damaged, do not force the card into
the station slot.
Do not strike the iron against hard objects to remove excess solder. This will damage the iron.
Be sure the work area is well ventilated. Soldering produces smoke.
While using HAKKO FX-952, don’t do anything which may cause bodily harm or physical damage.
NOTE :
A NOTE indicates a procedure or point that is important to the process being described.
5. OPERATION
Controls and displays
Controls
The front panel of the HAKKO FX-952 soldering
station has the following controls:
• Four control buttons:
– Initiates a data entry mode.
– End of sequence signal (terminates a phase of
a data entry mode); when pressed for less than
one second, displays settings already stored.
– Switches the display to IRON 1
• The display for the temperature and the
heat to the IRON 1 will show ON/OFF alter-
nately by pressing more than one second.
• Increases the value in the appropriate dis-
play window.
– Switches the display to IRON 2
• The display for the temperature and the
heat to the IRON 2 will show ON/OFF alter-
nately by pressing more than one second.
• Decreases the value in the appropriate dis-
play window.
Displays
The HAKKO FX-952 has a three-digit display element.
Depending upon the selected mode, it will display:
• Normal mode:
Sensor temperature (tip temperature)
• Data entry:
Selected quantity (see ‘data entry procedures’ for
exact characteristics)
• Temperature scale:
°
C or
°
F, depending upon selection
• Error detection:
Refer to ‘ERROR MESSAGES’ section
In addition, heater lamps will flash when the station
has reached the desired temperature, indicating
that it is ready for use.
An audible buzzer is provided to alert the operator when:
• The station has reached the set temperature. The
buzzer will sound once.
• When the low temperature threshold has been
crossed, the buzzer will sound continuously. This
buzzer will shutoff when the sensed temperature
returns to the acceptable range.
• The buzzer will sound once when sleep function is
activated and the tip temperature starts to decrease.
• When a foreign substance, an incompatible tip, or
the soldering end of the tip is inserted into the
HAKKO FM-2025, the display will blink and the
buzzer will sound continuously.
• The auto power shutoff is activated and the pow-
er to the heating element is shutoff, the buzzer
will sound three times.
l
Operation
1. Turn the power switch ON.
2. Once the temperature is reached, the buzzer
sounds. The heater lamp at the lower right of the
temperature display starts blinking.
CAUTION
The HAKKO FX-952 is preset at 350
°
C at the factory.
Check the temperature setting by pressing the button.
The set temperature will be displayed for two seconds.
CAUTION
Place the iron in the iron holder when not in use.
2005.1
MA01336JZ050119
Copyright © 2005 HAKKO Corporation. All Rights Reserved.
OVERSEAS AFFILIATES
U.S.A.: AMERICAN HAKKO PRODUCTS, INC.
TEL: (661) 294-0090 FAX: (661) 294-0096
Toll Free (800)88-HAKKO
4 2 5 5 6
http://www.hakkousa.com
HONG KONG: HAKKO DEVELOPMENT CO., LTD.
TEL: 2811-5588 FAX: 2590-0217
http://www.hakko.com.hk
E-mail:info@hakko.com.hk
HEAD OFFICE
TEL:+81-6-6561-3225 FAX:+81-6-6561-8466
http://www.hakko.com E-mail:sales@hakko.com
SINGAPORE: HAKKO PRODUCTS PTE., LTD.
TEL: 6748-2277 FAX: 6744-0033
http://www.hakko.com.sg
E-mail:sales@hakko.com.sg
Please access to the following address for the other Sales affiliates.
http://www.hakko.com/address
Thank you for purchasing HAKKO FX-952 soldering station.
Please read this manual before operating the HAKKO FX-952.
Keep this manual readily accessible for reference.
