background image

Hako Hamster 500 E

Changes Due to Machine Directive 2006/42/EC

Clean ahead

Preface
Modified text in paragraph Preface:
Before using the equipment for the first 
time, read this original manual thor-
oughly, act according to the information 
contained and keep it in a safe place for 
future reference or subsequent owners.
Intended use
Modified text in paragraph Intended 
Use:
Based on the conception, design and 
construction of the model introduced 
onto the market by us, the machine 
complies with the applicable basic safe-
ty and health requirements stipulated in 
the EC Directive (refer to Declaration of 
Conformity). This declaration is no long-
er considered valid in the event of mod-
ifications to the machine not authorized 
by us. The manufacturer is not deemed 
liable for any damage resulting from un-
authorized modifications to the ma-
chine.
General safety information
The machine may be used only for 
operation on plane areas with a maxi-
mum inclination of up to 2 %.

Disposal
New text in Chapter Introduction:
Render the machine inoperable. It must 
not represent a potential source of dan-
ger for children.
Dispose of the device according to the 
applicable local regulations. For further 
information on handling and recycling, 
please contact your authorized Hako 
dealer where you purchased the de-
vice.
Used batteries with the recycling sym-
bol contain reusable commodities. The 
heavy metals contained simultaneously 
represent a serious risk to health and to 
the environment. Never open batteries 
or damage them. Never touch, inhale or 
swallow any material inside batteries. 
Health hazard! Never allow batteries to 
pollute the environment. Risk of con-
taminating the ground and water!  In ac-
cordance with the symbol with the 
crossed out bin, these batteries must 
not be disposed of in domestic waste. 
The return and recycling of old batteries 
must be agreed on with your authorized 
Hako dealer in accordance with the Bat-
tery Law § 6 and § 8 (BattG)

Noise emission value
The sound pressure level (LpA) (at the 
ear of the operator) measured accord-
ing to DIN IEC 60335-2-72 under nor-
mal working conditions: 70 dB (A)
Measurement inaccuracy (KpA): 
2 dB (A)
Sound power level (LwAd) measured 
according to DIN EN 60335-2-72 under 
maximum working conditions: 
87dB (A)

Vibration
The weighted effective value of acceler-
ation, measured in accordance with 
ISO 5349-1, to which the upper parts of 
the body (hand-arm) are exposed under 
normal working conditions: 
< 2,5 m/s²
The weighted effective value of acceler-
ation, measured in accordance with 
ISO 2631-1, to which the upper parts of 
the body (feet-seat) are exposed under 
normal working conditions: 
< 0,5 m/s²

Hako Hamster 500 E

Changes Due to Machine Directive 2006/42/EC

Clean ahead

Preface
Modified text in paragraph Preface:
Before using the equipment for the first 
time, read this original manual thor-
oughly, act according to the information 
contained and keep it in a safe place for 
future reference or subsequent owners.
Intended use
Modified text in paragraph Intended 
Use:
Based on the conception, design and 
construction of the model introduced 
onto the market by us, the machine 
complies with the applicable basic safe-
ty and health requirements stipulated in 
the EC Directive (refer to Declaration of 
Conformity). This declaration is no long-
er considered valid in the event of mod-
ifications to the machine not authorized 
by us. The manufacturer is not deemed 
liable for any damage resulting from un-
authorized modifications to the ma-
chine.
General safety information
The machine may be used only for 
operation on plane areas with a maxi-
mum inclination of up to 2 %.

Disposal
New text in Chapter Introduction:
Render the machine inoperable. It must 
not represent a potential source of dan-
ger for children.
Dispose of the device according to the 
applicable local regulations. For further 
information on handling and recycling, 
please contact your authorized Hako 
dealer where you purchased the de-
vice.
Used batteries with the recycling sym-
bol contain reusable commodities. The 
heavy metals contained simultaneously 
represent a serious risk to health and to 
the environment. Never open batteries 
or damage them. Never touch, inhale or 
swallow any material inside batteries. 
Health hazard! Never allow batteries to 
pollute the environment. Risk of con-
taminating the ground and water!  In ac-
cordance with the symbol with the 
crossed out bin, these batteries must 
not be disposed of in domestic waste. 
The return and recycling of old batteries 
must be agreed on with your authorized 
Hako dealer in accordance with the Bat-
tery Law § 6 and § 8 (BattG)

Noise emission value
The sound pressure level (LpA) (at the 
ear of the operator) measured accord-
ing to DIN IEC 60335-2-72 under nor-
mal working conditions: 70 dB (A)
Measurement inaccuracy (KpA): 
2 dB (A)
Sound power level (LwAd) measured 
according to DIN EN 60335-2-72 under 
maximum working conditions: 
87dB (A)

Vibration
The weighted effective value of acceler-
ation, measured in accordance with 
ISO 5349-1, to which the upper parts of 
the body (hand-arm) are exposed under 
normal working conditions: 
< 2,5 m/s²
The weighted effective value of acceler-
ation, measured in accordance with 
ISO 2631-1, to which the upper parts of 
the body (feet-seat) are exposed under 
normal working conditions: 
< 0,5 m/s²

Summary of Contents for Hamster 500 E







































Reviews: