Halco J&J Electronics ColorSplash VU LPL-R1C-12..., Installation And Operation Manual

11

12

Show: 

Slow color-fade through orange, red and magenta. 

Cycle: 

Continuous color sequence cycle with cross-fade between colors. 

6. DESERT SKIES:

Show: 

Fast color-change through random colors. 

Cycle: 

Light will hold on each color for 2 seconds before changing to the next color.

7. NOVA:

8. PARISIAN BLUE: 

Solid Deep Blue

9. NEW ZEALAND GREEN: 

Solid Deep Green

10. BRAZILIAN RED: 

Solid Deep Red 

11. ARCTIC WHITE: 

Solid White  Hue 

12. MIAMI PINK: 

Solid Deep Pink

1.  Verify the VÜ Nicheless LED Underwater Light has been disconnected from the power source  

  and be sure the light fixture is in a dry environment. Remove the screws from the lens with  

  the tool provided. Pull the lens from the body of the fixture.
2.  Using the tool provided, insert and turn the threaded portion into the extraction hole in the  

  face of the light cartridge. Pull the light cartridge from the body of the housing.
3.  Insert the replacement cartridge into the body of the housing. Line up the tab at the end of the  

  circuit board with the receiving slot inside the body of the housing. It may be necessary to  

  slowly turn the light cartridge until the tab lines up with the slot.
4.  Clean the lens and the enclosure of any remaining old silicone sealer before applying new silicone  

  and replacing the lens. Replace the O-ring with the new one provided. Attach the lens onto the  

  fixture body. Tightly secure the screws . Once all screws are tight, slowly submerse the fixture in water,  

  checking for any air bubbles. Immediately remove fixture from water if air bubbles appear, as this indicates  

  the seal is not on correctly, leaving it not water tight. Retighten the screws and test for air bubbles again. 

5.  Reset the fixture into the wall fitting and trun the power on.

Which could result in serious injury or death. The 

VÜ Nicheless LED Lights

 are only available for 12VAC 

power. For supply connection, use only an isolating low voltage power supply with ungrounded output, 

evaluated and listed by a Nationally Recognized Testing Laboratory (NRTL) for swimming pool use.

RISK OF ELECTRIC SHOCK OR ELECTROCUTION.

WARNING

LIGHT CARTRIDGE REPLACEMENT

The water level should be lowered to approximately 12 inches below the pool lights. Be certain the water 

is drained out of the wall housing. Minimum pool safeguard requires dropping the water level 2 inches 

to 4 inches below the light. NEVER remove water from the pool without checking ground water tables.

WINTERIZING

Consult a local state or city swimming pool professional for proper winterization of 

your

VÜ Nicheless LED Underwater Light Fixtures.

WARNING

Use the following tips to help you resolve problems that might occur while operating the 

VÜ Nicheless LED Underwater Light Fixtures.

TROUBLESHOOTING

Problem 

Possible Cause/Action

All lights fail to  

illuminate 

One or more lights 

are dim, blinking or 

not working 

Colored lights out  

of sync

Lights are not receiving 

power 

Poor connection of 

improper wire gauge 

Improper voltage  

supply or poor  

connection to the light

Check 120VAC power supply into transformer. 

Check for 12VAC output at transformer. Check 

or reset GFCI. Make sure 120 volts has not been 

used in the installation - damage is assured and 

will void the warranty. 

 Separate each light and independently wire 

12VAC to this single light only. Repeat this pro-

cess on each light. If junction box is being used, 

check for proper connection of light cord. Verify 

that the correct wire gauge is being used  

between the transformer and the j-box. 

 Verify that proper wire connections are being 

achieved for the lights that are out of sync. Reset 

all the lights to white by turning lights OFF for 

five (5) seconds, then turning ON.