background image

2021.05.25 

• 

REV. 3 

• MASS FLOW METER OPERATING MANUAL

 17

Display Setup

MENU 

 SETUP 

 Display

The options in the 

display setup menu

 adjust the contrast/brightness of the display and 

enable screen rotation.

Main Screen Options

SETUP 

 Display 

 MAIN Screen

• 

Any Key Press

 changes what happens when any of the parameter buttons on the 

main 

display

 (

page 10

) are pressed (pressure or temperature, for example). By default, 

these buttons highlight their measurement in the center of the display. If this option is 

set to 

Show Actions Menu

, an option to change that parameter’s engineering units will 

be shown, as well as an option to highlight the parameter.

• 

Top Left Key Value

 will show if the device has an optional barometer installed. This 

option configures which type of pressure (barometric, gauge, absolute) is displayed.

Screen Lighting

SETUP 

 Display 

 Screen Lighting

The options and wording in the 

screen lighting menu

 will vary for monochrome versus 

color displays.

• 

On monochrome displays, press 

LESS CONTRAST

 or 

MORE CONTRAST

 to adjust the contrast 

levels and move the contrast indicator left or right. 

POWER UP Lit

 or 

Dark

 toggles whether 

the backlight of the unit will be on when the device powers on.

• 

On color displays, press 

DIMMER 

or 

BRIGHTER 

to adjust the brightness level and move 

the brightness indicator left or right.

Display Rotation

SETUP 

 Display 

 Display Rotation

The device has the option of inverting (flipping) the screen upside-down, as configured in 

this menu.

Advanced Setup

MENU 

 SETUP 

 Advanced

The 

advanced setup menu

 contains settings and detailed information that are useful when 

troubleshooting with customer support.

Factory Restore

SETUP 

 Advanced 

 Factory Restore

This will immediately take you to a confirmation screen. When troubleshooting, an appli-

cations engineer may recommend doing a 

Factory Restore

. If something is not acting as 

expected, please contact an applications engineer prior to doing a 

Factory Restore

.

Register Status

SETUP 

 Advanced 

 Register Status

The 

Register Status

 screen displays live values for the internal device registers. Many of 

these values can help an applications engineer diagnose operational issues over the phone. 

Some register values clearly distinguish between hardware and operational problems, which 

speeds up the troubleshooting process. 

Edit Register and Device Properties

SETUP 

 Advanced 

 Edit Register

SETUP 

 Advanced 

 Device Properties

 !

 Warning: 

Editing these settings may cause the device to become inoperable. Do not 

modify them without working with an applications engineer.

The 

display setup menu

.

The options for pressing buttons 

on the 

main display

.

The 

monochrome contrast menu

.

The 

advanced setup menu

.

The register status list.

Summary of Contents for ALICAT SCIENTIFIC M































Reviews: