background image

2021.05.25 

• 

REV. 3 

• MASS FLOW METER OPERATING MANUAL

 13

Setup

Gas Selection

MENU 

 SETUP 

 Active Gas

Gas Select™

Most flow meters are physically calibrated at the factory using air. Gas Select™ allows you 

to reconfigure the flow meter to flow a different gas without any need to send it back for a 

physical recalibration.
Within this menu, there are a variety of categories (such as 

Standard

Chromatography 

and 

Welding

), as well as recent selections, and COMPOSER™ mixes (see below). Each category 

will list a subset of available gases and preconfigured mixtures.
As soon as you press 

SET

 from the gas list, your flow meter will reconfigure its flow rate 

calculations to the newly selected gas’s properties. There is no need to restart the device.
Your current gas selection appears just below the unit’s indicator on the right side of the 

main display

 (

page 10

).

Category and Gas List Controls

• 

PAGE

 advances the view to the next page of categories or gases.

• 

SELECT

 (in the category list) opens a list of gases in that category.

• 

SET

 (in the gas list) immediately loads the gas measurement properties and exits to the 

setup menu

.

Using COMPOSER™ Gas Mixes

SETUP 

 Active Gas 

 COMPOSER Mixes

To provide accurate measurements, your flow meter needs to reference the viscosity 

of the gas you are flowing through it. The closer you can get to defining your actual gas 

composition, the more accurate your flow readings will be. COMPOSER™ is an included feature 

of Gas Select™ that lets you define new mixed gas compositions to reconfigure your flow 

meter whenever needed.
Wilke’s semi-empirical method is used to define a new gas mixture based on the molar 

(volumetric) ratios of the gases in the mixture. You can define these gas compositions to 

within 0.01% for each of up to five constituent gases in the mixture. Once you define and 

save a new COMPOSER™ gas mix, it becomes part of the Gas Select™ system and is accessible 

under the gas category 

COMPOSER

 

User

 

Mixes

. You can store up to 20 COMPOSER™ gas mixes 

on your flow meter simultaneously.

 ✓

 Note: 

The COMPOSER™ device firmware does not physically mix gases. It only configures 

the device’s calculations to report flow readings more accurately based on the constituent 

gases of your defined mixture.

Select any existing mix and press 

SET

 to immediately configure your device to measure that 

gas mixture. To create new mixes, see the next section.

The first page of the Gas Select™ 

category list.

The 

setup menu

.

The Gas Select™ standard gas list.

Summary of Contents for ALICAT SCIENTIFIC M































Reviews: