Hama CC 612L, Operating Instructions Manual

3

INSTALLATION:

1.  Place the shredder on the rim of the waste paper basket.

2.  Connect the power cable to a 220~240 V socket.

3.  Set the switch to “AUTO”. If the green light does not 

  illuminate after doing this, reposition the shredder 

  correctly on the paper basket.

MODES:

Using the switch on the device, select one of the following 

modes.

AUTO

 – On this setting, the shredder switches itself on 

automatically as soon as you insert paper into the paper 

feeder. It switches off automatically after there is no more 

paper.

REV

 – In the unlikely case of paper being trapped in the cut-

ter, the reverse function allows you to remove the blockage.

OFF

 – This setting switches off the shredder.

SLITTING CAPACITY:

The CC 612L can shred up to 5 sheets of 70 g/m² paper with 

a maximum width of 220 mm at the same time.

A FOLDED SHEET OF PAPER IS THE EQUIVALENT OF TWO 

SHEETS!

WARNING:

1.  Ensure you do not insert things such as clothes, ties, 

  jewellery or hair into the paper feeder.

2.  Set the switch to “OFF” if you will not use the shredder 

  for a prolonged period of time.

3.  Remove any paper clips and staples from the paper 

  before shredding. The shredder will not break if you 

  forget to do this once. However, you should normally 

  avoid this.

4.  Keep hands and fi ngers away from the underside of the 

  shredder during operation and especially the cutting 

  roller, as this can cause serious injury.

5.  The runtime of the shredder should not exceed two 

  minutes at a time. If you happen to have a large quantity 

  of paper to shred, we recommend that you switch off the 

  shredder after 2 minutes of continuous operation and 

  wait 15 minutes before switching the shredder back on 

  again.

6.  The socket you use should be close to the shredder and 

  be easily accessible.

7.  Always switch the shredder off (or remove the mains 

  plug) before moving or cleaning the shredder or 

  emptying the paper basket.

8.  Empty the paper basket regularly.

PAPER BLOCKAGE AND OVERLOAD PREVENTION:

The CC 612L has a motor  with an overload prevention 

function. The normal operating cycle for uninterrupted 

shredding activity is 2 minutes continuous operation follo-

wed by 15 minutes switched off. The shredder could switch 

off automatically in the following situations:

1.  If the shredder is used for more than two minutes at a 

  time.

2.  If it becomes overloaded due to more than fi ve sheets of 

  paper being fed into the shredder at a time, or if the 

  paper is not fed into the shredder evenly.

Both cases could trigger the automatic overload prevention 

function, which interrupts the power supply. If this is the 

case, proceed as follows:

1.  Remove the plug from the socket and wait at least 15 

  minutes until the overload prevention function resets. 

  Remove all remaining paper from the shredder or cut it 

  off in an appropriate way.

2.  Connect the machine to the mains again and set the 

  switch to “REV”. Using the reverse function, feed the 

  paper trapped in the cutting roller out of the top of the 

  shredder.  You can then set the switch back to “AUTO”.

3.  If the switch is set to “AUTO” and the paper feeder is 

  clear, the shredder is now ready to use again.

SPECIFICATIONS:

•  Cutting size: 4x39 mm (cross cut)

•  Cutting capacity: 5 sheets

•  Cutting speed: 2.4 m/min.

•  Max. feeding width: 220 mm

•  Mains supply: 220~240 V

•  Measurements of the CC 612L: 380x160x360 mm

g

Operating Instructions