I
II
III
A
A
B
C
A
B
B
D
C
E
1
2
1
2
3
4
3
2
1
G
Operating instruction
Thank you for choosing a Hama product.
Take your time and read the following instructions and informa-
tion completely. Please keep these instructions in a safe place
for future reference.
1. Explanation of Warning Symbols and Notes
Warning
This symbol is used to indicate safety instructions or to draw
your attention to specific hazards and risks.
Note
This symbol is used to indicate additional information or
important notes.
2. Safety Notes
•
Use the product for its intended purpose only.
•
Protect the product from dirt, moisture and overheating, and
only use it in a dry environment.
•
When using this product, observe the applicable local traffic
laws and regulations.
•
Do not drop the product and do not expose it to any major
shocks.
•
Keep the packaging material out of the reach of children due
to the risk of suffocation.
•
Dispose of packaging material immediately according to
locally applicable regulations.
•
Do not modify the product in any way. Doing so voids the
warranty.
3. Montage
Note
•
Before mounting the holder, check the installation options
in your vehicle. If in doubt, consult the manual for your
vehicle or contact the manufacturer.
•
Never apply force when using the product or during
installation.
Warning
•
Take care that components such as airbags, safety areas,
controls, instruments, etc. and visibility are not blocked or
restricted.
•
Do not allow yourself to be distracted by the product,
for example when driving a vehicle or operating sports
equipment. Always pay attention to the surrounding traffic
and your environment.
Pictures for illustration only!
The use of the product you’ve purchased may differ slightly.
If you have difficulties installing or questions about the product,
please call our support line (see
5. Service und Support
).
3.1 Attaching the holder (I)
Ventilation grille clamp (A)
•
Carefully push the ventilation grille clamp onto the open
panels of the ventilation grille until it locks into place.
Note
Before setting a device in the holder, check that the panels
are sturdy enough to bear the weight. We recommend against
using this model for terminal devices heavier than 300 g.
•
To remove the holder, use a suitable tool (such as a screw-
driver) to gently press the locking pin downwards and then
carefully pull the holder out of the ventilation grille.
Screw-fastening (B)
Note
Make sure that there are no cables or pipes underneath the
selected installation site that might be damaged.
•
Use suitable screws to fasten the holder to the selected
installation site.
Adhesive pad (C)
Note – Installation surface
Please note that the selected installation surface (e.g.
dashboard) should be free of dust and grease. Use a suitable
cleaning agent from a specialised dealer to clean the surface.
•
(Remove one of the protective films from the adhesive pad and
press it onto the rear side of the holder for a few seconds.)
•
Remove the (other) protective film from the adhesive pad and
gently press the holder onto the selected installation surface.
Note
•
Wait at least 24 hours after installing the adhesive pad
before attaching the holder.
•
Note that the adhesive pad is permanently attached. To
remove the adhesive pad, carefully pull it off the installation
surface. The adhesive pad can only be attached again using
suitable adhesive material available from specialised dealers.
•
Various environmental factors such as ambient humidity,
sunlight or cold can impair the durability of the adhesive pad.
•
We cannot guarantee that residue will not be left on the
mounting surface after the adhesive pad is removed.
Handlebar clamp (D)
Note
Make sure that the installation will not result in any control
elements, cables, instruments, etc. being covered up,
pinched, or impaired in their functioning.
•
Use a suitable tool (optionally included), loosen the screws to
open the clamp and attach it to the handlebar.
•
If necessary, use rubber pads or adapters (optionally included)
to adjust the clamp to fit the diameter of the handlebar.
•
Close the clamp and fasten it in place by tightening the screws.
Suction cup holder (E)
•
Remove the protective film from the suction cup and position
it on a clean and flat surface (e.g. window pane).
•
If the suction cup holder is to be attached to a rough or une-
ven surface (e.g. a dashboard), an adapter plate is optionally
available.
•
Push the locking lever (E – 1) to fasten the suction cup.
•
Open the clamping device (E – 4) to position the carrying arm.
•
Close the clamping device to lock this position.
•
To release the suction cup from the surface, pull the lateral
slides in the direction of the arrow. (E – 2) Then gently pull the
flap to completely release the suction cup. (E – 3)
3.2 Mounting the holder (II)
Clip system (A) / 4-hook/hole clip system (B)
•
Set the recess or recesses of the holder onto the bracket.
•
Move the holder up or down until it clicks into place or is
seated firmly.
4-hook/hole clip system – QuickFIX (C)
•
Press the buttons on the side of the bracket together. Then set
the recesses on the rear of the holder onto the hooks of the
bracket. Let go of the buttons to engage the mounting clip
and fasten the holder in place.
•
To remove the holder, press the buttons on the side of the
bracket together. The clip system disengages and you can
remove the holder.
3.3 Inserting and removing terminal devices (III)
Note
•
Always take your terminal device out of the holder before
attaching or removing the bracket (adhesive pad, suction
cup holder, ventilation grille clamp or other).
•
If using a handlebar clamp (I-D), use only a (universal)
attachment system that additionally secures the terminal
device from falling or protects it from resulting damage
(such as prods. no. 88404, 88415, 91324, 93710).
Suitable attachment systems for handlebar mounting are,
for instance, protective bags, brackets with elastic straps,
etc. (such as prods. no. 93830, 93778)
Universal bracket A
•
Press the button on the side of the universal bracket to open
the retaining jaws. (A – 1)
•
Insert the terminal device of your choice and secure it in place
by lightly pushing the retaining jaws together. (A – 2)
•
Also adjust the lower carrying arms to the terminal device by
pulling them further apart or pushing them closer together.
(A – 3)
•
In order to easily remove the terminal device, press the button
on the side of the universal holder. (A – 1)
Universal bracket B
•
Turn the small wheel in the direction indicated by the arrow/
anti-clockwise to open the retaining jaws. (B – 1)
•
Insert the terminal device of your choice and secure it in place
by lightly pushing the retaining jaws together. (B – 2)
•
Adjust both the height and the depth of the retaining jaw
fixtures to your terminal device by pulling them further apart
or pushing them closer together. (B – 2)
•
Also adjust the lower carrying arms to the terminal device by
pulling them further apart or pushing them closer together.
(B – 3)
•
Remove the bottom/top covering cap to add or remove carry-
ing arms. Replace the covering cap once the adjustments to fit
your terminal device have been made. (B – 4)
Note
When using the universal bracket, use as many adjustable
mountings as are necessary for the terminal device to be
perfectly seated. To prevent the device from falling out, push
the retaining jaws securely together.
4. Warranty Disclaimer
Hama GmbH & Co. KG assumes no liability and provides no war-
ranty for damage resulting from improper installation/mounting,
improper use of the product or from failure to observe the
operating instructions and/or safety notes.
5. Service and Support
Please contact Hama Product Consulting if you have any ques-
tions about this product.
Hotline: +49 9091 502-115 (German/English)
Further support information can be found here: www.hama.com
All listed brands are trademarks of the corresponding companies. Errors and omissions
excepted, and subject to technical changes. Our general terms of delivery and payment
are applied.
Hama GmbH & Co KG
86652 Monheim/Germany
www.hama.com
000884000030/11.15
1
3
2
2
4
