6
7
- Select the headset and follow the remaining
instructions in the phone or in the operating instructions
of the phone.
- If you are asked for the passkey or PIN, confi rm this by
entering 0000.
- Pairing is now complete. The yellow LED goes out
and the LED now fl ashes blue regularly (approx. every
2 seconds). This indicates that the headset is ready for
operation (standby). The headset is now ready for
operation and can be used.
Use/Call management
Answering calls
You can answer incoming calls using the headset. Incoming
calls are signalled audibly in the headset. Press the „ON/
OFF“ button – the call is accepted.
Ending calls
Press the „ON/OFF“ button to end calls.
Making calls
Ensure that your headset is „connected“ to the telephone.
Calls are made as usual, with the exception that the
headset is used to make the call.
Making calls using voice dialling
To make calls using voice dialling, the corresponding voice
profi les must be set up/stored in your phone. Your telephone
must also support this function in Bluetooth mode (hands-
free profi les only). For more information, please refer to the
operating instructions of your mobile phone. Voice dialling
using the headset operates in the same manner as if you
were making a call using the phone. The only difference is
that voice dialling is activated using the headset, not the
phone.
- Press the “ON/OFF” button.
- A short tone indicates that voice dialling has been
activated.
- Say the correct name or the voice profi le of the person
you wish to call.
- The call will be made.
Transferring calls (hands-free profi les only)
Press and hold the „ON/OFF“ button for approx. 3 seconds
to transfer calls from the headset to the mobile phone as
well as from the mobile phone to the headset during a call.
Please note:
With some mobile phones, the connection between the
telephone and the headset is automatically disconnected
after a certain period, or the devices must be connected
manually after both devices (headset and mobile phone) are
switched on. If this is the case, no call signal is heard via
the headset for incoming calls. To establish the connection
for incoming calls, press the „ON/OFF“ button.
Volume control
Press the volume button to set the volume of the headset
as required. The volume can also be controlled via the
telephone.
Music playback
The headset can be used for music playback in combination
with various playback devices (mobile phone, MP3-player,
PC/laptop, etc). However, keep in mind that the headset is
only compatible with components that support one of the
required Bluetooth profi les (A2DP or AVRCP) for stereo
playback.
Suitable devices must also have an identical PIN code:
0000 or allow this PIN code to be assigned to them (mobile
phone, PC/laptop).
We recommend also following the operating instructions
for the selected devices when carrying out the pairing
procedure.
Remote control functions
If your playback device (MP3-player, mobile phone, etc.)
supports the Bluetooth profi le „AVRCP“ (Audio Video
Remote Control Profi le), then the player can be controlled
remotely from the headset. The functions Play/Pause,
Forward, and Back can be carried out.
Music playback with a mobile phone
For more information on music playback via Bluetooth
stereo, please refer to the operating instructions of your
mobile phone. You can also use the headset to make
telephone calls during music playback with your mobile
phone. As soon as you activate the telephoning function (for
example, when you make a call), music playback is stopped
until the telephoning function is ended. Then the music
playback continues.
Troubleshooting
If you cannot connect, pair or operate the headset with your
mobile phone, we recommend that you check the following:
- Ensure that the headset is fully charged. Switch the
headset off and on again.
- Ensure that Bluetooth is activated on your phone.
- Ensure that your headset is paired to the telephone.
- Note that the max. range of the Bluetooth connection
between the telephone and headset is approx. 10
metres. However, this depends on the environment
(walls, electronic devices, etc.).
Precautionary measures and caring for your Bluetooth
headset
- Switch off the headset before storing it in your pocket
or elsewhere to prevent accepting calls unintentionally.
- Keep the headset away from liquids, moisture and dirt.
- Do not use aggressive cleaning agents to clean the
headset.
- Do not expose the headset to excessively high or low
temperatures.
- If you are not going to use the headset for an extended
period, store it in a dry place and protect it against
excessive temperatures.
- Note that the integrated battery cannot be changed. Do
not try to open the housing of the headset.
- Use only the enclosed USB-cable to
charge the headset.
Registration and safety certifi cation/general information
This device bears the CE symbol as specifi ed by the
provisions of Directive R & TTE (1999/5/EC).
Hama GmbH & Co KG hereby declares that this device is in
compliance with the basic requirements and other relevant
regulations of the 1995/5/EC guideline. The declaration of
conformity can be viewed online at http://www.hama.com.
00087501bda.indd Abs2:6-Abs2:7
00087501bda.indd Abs2:6-Abs2:7
18.02.2009 8:50:55 Uhr
18.02.2009 8:50:55 Uhr
