Subject to change without notice
31
(8)
RV6021 : Astigmatism correction.
Locate and identify RV6021 (8) on CRT-Board.
Connect a 1MHz squarewave signal with 25mVpp at 50
Ω
(HZ22) to input CHI.
Set time base to 0.1µs/div.
Adjust FOCUS control for optimum sharpness.
Adjust RV6021 (8) until leading edge and top of signal have equal sharpness.
Recheck range of FOCUS control.
Adjust FOCUS control for optimum sharpness.
(9)
R640: Y-Gain CH I.
Locate and identify R640 (9) on YPA-Board.
Connect a 25mV/1kHz squarewave signal via 50
Ω
cable and 50
Ω
through terminator
to input channel I.
Set time base to 1ms/div.
Adjust R640 (9) for 5 division signal height.
(10) R122: FET operating point CH I.
Locate and identify R122 (10) in CH I section of the YPA-Board.
Release all pushbuttons (out!) for channel I mode.
Press Y x5 channel I (in!) for 1mV/div.
Press GD pushbutton channel I (in!).
Switch the attenuator channel I constantly between 5mV/div (1mV) and 10mV/div (2mV).
Adjust R122 (10) until no Y-position change occurs.
Do not change the operating conditions.
(11) R203: Invert-Balance CH I.
Press GD pushbutton channel I (in!).
Press Y x5 channel I (in!) for 1mV/div.
Using Y-POS.I control set trace to the horizontal center line.
Locate and identify R203 (11) on YPA-Board.
Adjust R203 (11) so that the baseline will not move, when pressing and releasing the
INVERT CH I pushbutton.
(12) R177: Variable-Balance CH I.
Locate and identify VR177 (12) in CH I section of the YPA-Board.
Press channel I Y-MAG. x5 pushbutton for 1mV/div.
Press channel I GD pushbutton (in!).
Adjust VR177 (12) so that the baseline will not move when turning the channel I Y-variable
control through the entire range.
Check adjustment 11) again and repeat it if required.
Summary of Contents for HM 303-4
