130
© HAMILTON 2011 – INSTRUCTION MANUAL
© HAMILTON 2011 – INSTRUCTION MANUAL
131
3.
操作说明
3.6
自动 GMT 表
机芯:
2893-1 • 2893-2
设置时间
1.
将表冠
C
完全拉至位置 (
p2
) :秒针停止。
2.
将表冠向需要的方向旋转,设置时间。
3.
将表冠完全推回位置 (
p0
):秒针重新开始走动,
从而达到与时间信号的完美同步。
设置日期和世界时指示盘或 24 小时指针(根据
型号)
1.
将表冠
C
拉至位置 (
p1
)。
2.
逆时针旋转表冠来设置日期,顺时针旋转来设
置 24 小时指针
3.
将表冠完全推回。
注意 : 在晚上 8 点和次日凌晨 2 点之间无法进行
日期调校。
机芯:
2893-3
设置时间
1.
将表冠
C
完全拉至位置 (
p2
) :秒针停止。
2.
将表冠向需要的方向旋转,设置时间。
3.
将表冠完全推回位置 (
p0
):秒针重新开始走动,
从而达到与时间信号的完美同步。
设定世界时指针
1.
将表冠
C
拉至位置 (
p1
)。
2.
将表冠向需要的方向旋转,设置世界时指示盘。
3.
将表冠完全推回。
4.
关键词
4.1
旋入式表冠
在某些型号上,表冠
C
是旋入的,以保证最佳防
水性。要进行调校,必须将其旋开。调校完毕后,
确保将它重新旋入。
> 只有将表冠旋入,防水性才能得到保证。
4.2
测距仪
显示声音在一定时间内通过的距离的刻度。例如,
要测量您与雷暴之间的距离,在您看到闪电时启
动计时器,听到雷声时停止。3 秒的测量结果将
在测距仪刻度上得到 1 公里的距离。
4.3
视距仪或英里视距仪
显示车辆平均速度的刻度。使用计时器的启停功
能,测量通过 1 公里或 1 英里的时间。可以在视
距仪或英里视距仪刻度上读出平均速度。
示例 :20 秒钟通过 1 公里或 1 英里 = 180 公里 /
小时或 180 英里 / 小时
4.4
氦气阀
氦气阀用于在潜水钟中停留数天时间的潜水员。
潜水站或潜水钟中的空气富含氦气以利于呼吸。
氦气能够透过接缝渗入表中。但是,遗憾的是,
它不能从接缝中逸出。为了提供更多的压力使其
逸出,在上升时打开氦气阀。
4.5
EOL 功能
表示电池寿命的终止。如果秒针开始以每次 4 秒
的幅度走动,应请您的汉米尔顿代理商更换电池。
4.6
动力储备
用于检查您的自动表的运转动力储备情况的指
针。
4.7
GMT
格林尼治标准时间(GMT)是全年相同的全球时
间系统。在手表行业,GMT 指在表盘上同时显示
两个或多个时区的计时器。
4.8
月相
一个跟踪月球相位的指针。设置后,月相指针准
确地显示月球的相位。
4.9
COSC
瑞士官方精密时计检测中心——一家瑞士检测机
构,对表(更确切地说是机芯)进行“精密时计”
认证。每个机芯都要逐个在不同的地点和温度下
进行 15 天以上的检测,只有那些每天误差不超过
5 秒的机芯才能通过认证。
4.10
旋转外表圈计时
测量所用时间的刻度
1.
逆时针旋转表圈
F
,将小箭头对准分针。
2.
分针指向的旋转表圈上的刻度即是所经过的时
间。
4.11
倒计时功能
1.
旋开表冠。
2.
旋转表冠,使旋转表圈上所需的倒计时时间刻
度对准分针
3.
重新旋入表冠。
4.
当分针指向旋转表圈上的小箭头时,倒计时完
毕。