Hamilton HAMILTON AM1000 Installation Manual Download | Manualshive

Page: 3 / 22

background image

Item Vendor

Aprox
Cost Notes

AM1000C AM1000A Trans-
mitter

RangeMas-
ter

Depends on discount Outdoor transmitter "C" ver-
sion is crystal and "A" version is agile (set frequen-
cy with switches)

AM1000BR mount bracket

RangeMas-
ter

Mounts transmitter to 1 1/4 " mast

AM1000WR 100" wire

RangeMas-
ter

2 pair (one pair for power, the other for audio) #22
with shield. Wire should not be bigger then .25"
diameter, the weatherproof cable grip opening in
the box is .25" Can Use Cat 5 Wire Also

AM1000ANT 102" whip an-
tenna

RangeMas-
ter

Standard Citizens band whip antenna, with 5/8 x
24 base. Available at Radio Shack (21-903) or any
CB shop.

Ground Rod 4 foot

Radio Shack

$13 Radio Shack 15-530

Ground Rod 8 Foot

Lowes or
Home Depot

$10

Used to ground electrical meters, 5/8 x 8" copper
clad

Ground Rod wire clamp

Lowes or
Home Depot

$4

Connect wire to Ground Rod (All connections must
be soldered with electrical type rosin core solder
using torch or tightly clamped and then weather-
proofed.

Ground wire

Lowes or
Home Depot $30-40

Use #12-#10, the bigger wire (10) will give better
performance but will be harder to work with. 500ft
roll. Insulated is fine.

Wire mounting hardware

Lowes or
Home Depot

$15

Think about how you are going to mount the
ground wire, it needs to be tied down (mounted to
the side of the building or pole) so it won't move
(see instructions)

15-891 Eaves mount

Radio Shack

$16 Or any antenna store

15-893 Vent mount

Radio Shack

15-517 Tripod mount

Radio Shack

$33

15-886 Wall mount

Radio Shack

15-839 Chimney mount

Radio Shack

$25

15-889 roof mount

Radio Shack

15-885 Wall mount

Radio Shack

$20

15-863 10' 1 1/4 mast

Radio Shack

$18 10' long mast to mount the transmitter. There is

Guy wire supplies

Antenna

If

needed

VOM meter

RangeMas-
ter or Radio
Shack $10-30

If you don't have one get one from Radio Shack.
Needed for tuneup.

Audio Adapter

May be needed if you need to convert unbalanced
audio to balanced (see instructions) (Item# )555-

Power supply 16 VDC

RangeMas-
ter

Free

Included with the AM1000.

Tuning tool

RangeMas-
ter

Free

Needed for tuneup

Complete instructions

RangeMas-
ter

Free

Manual with installation video

1.1 Some addition Items

3

«
1
2
3
4
5
...
»

Summary of Contents for HAMILTON AM1000























Reviews:

No comments

Related manuals for HAMILTON AM1000

Brand: halstrup-walcher Pages: 34

Brand: Camsat Pages: 2

Brand: Camsat Pages: 2

Brand: Jung Pages: 5

Brand: Omega Pages: 32

Brand: NAPCO Pages: 4

Brand: Camille Bauer Pages: 32

Brand: Hallicrafters Pages: 30

Brand: Kimo Pages: 32

Brand: MELICONI Pages: 24

Brand: Kubu, inc. Pages: 6

Brand: Icom Pages: 47

Brand: Emcee Pages: 77

Brand: Icom Pages: 78

Brand: Icom Pages: 124

VHF MARINE TRANSCEIVER IC-M501EURO

Brand: Icom Pages: 34

TX-500-120-240-50-60-AC

Brand: Larson Electronics Pages: 2

Brand: autosen Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands