background image

14

Operation (continued)

OPERATING YOUR FAN AND REMOTE CONTROL

NOTE:

 

The fan will store the last used speed setting for the 

next time it is turned on.

Pressing the       button will activate the Comfort Breeze

TM

 mode. 

If you are using Comfort Breeze

TM

 mode, pressing the       button 

or the fan speed buttons will cancel Comfort Breeze

TM

 mode 

and resume normal fan operation.

Pressing the timer button will automatically turn fan off 

after 2, 4, or 8 hours. To cancel the timer settings, press 

and hold the button three seconds and the signal light will 

flash.

2

HR

4

HR

8

HR

Fan 

ON/OFF

 button: Press and release this button to turn the 

fan on or off. 

Fan 

9 SPEED

 button: Press and release the “

+”

 button to 

increases the fan speed. Press and release the “

-”

 button to 

decreases the fan speed. 

Forward, press and hold the button three seconds and the 

signal light will flash.

SUMMER

Reverse, press and hold the button three seconds and the 

signal light will flash.

WINTER

Fan on/off 

Fan on/

Increases / 

decreases 

fan speed

Comfort Breeze

TM

Timer

Signal light

Reverse

Forward

Summary of Contents for DANETREE N243B-BN


















Reviews: