HAMPTON BAY Edgemont 324-848 Owner'S Manual Download

Page: 10 / 17

WARNING

MAKE SURE THE TAB ON THE HANGER BRACKET PROPERLY SITS IN THE GROOVE IN THE

HANGER BALL BEFORE ATTACHING THE CANOPY TO THE BRACKET BY TURNING THE

HOUSING UNTIL IT DROPS INTO PLACE.

Tuck connections neatly into ceiling outlet box.

Slide the canopy up to mounting bracket and place the key hole on the canopy over the screw on the
mounting bracket, turn canopy until it locks in place at the narrow section of the key holes. (Fig. 10)

Align the circular hole on canopy with the remaining hole on the mounting bracket, secure by
tightening the two set screws.

Note:

Adjust the canopy screws as necessary until the canopy and

canopy cover are snug.

Finishing the Fan Installation

Figure 10

Outlet Box

Ceiling
Mounting
Bracket

Screw

Canopy

Canopy
Bottom Cover

Summary of Contents for Edgemont 324-848


















Search results

Summary of Contents for Edgemont 324-848

Reviews:

Related manuals for Edgemont 324-848

Brands by name

Popular brands

HAMPTON BAY Edgemont 324-848, Owner'S Manual

Search results

Summary of Contents for Edgemont 324-848

Reviews:

Related manuals for Edgemont 324-848

Brands by name

Popular brands