background image

Care of Your Fan 10.

Here are some suggestions to help you maintain 
your fan

1.Because of the fan's natural movement, some 

connections may become loose. Check the 
support connections, brackets, and blade 
attachments twice a year.  Make sure they are 
secure. (It is not necessary to remove fan from 
ceiling.)

2. Clean your fan periodically to help maintain 

its new appearance over the years.  Use only a 
soft brush or lint-free cloth to avoid scratching 
the finish.  The plating is sealed with a lacquer 
to minimize discoloration or tarnishing. Do 
not use water when cleaning. This could 
damage the motor, or the wood, or possibly 
cause an electrical shock.

3. You can apply a light coat of furniture polish 

to the wood blades for additional protection 
and enhanced beauty. Cover small scratches 
with a light application of shoe polish.

4. There is no need to oil your fan.  The motor 

has permanently lubricated bearings.

IMPORTANT

MAKE SURE THE POWER IS OFF AT 

THE  ELECTRICAL PANEL BOX 

BEFORE YOU ATTEMPT ANY 

REPAIRS.  REFER TO THE

SECTION "MAKING ELECTRICAL 

CONNECTIONS".

Touching
ceiling

Figure 17

Summary of Contents for WITHROP 656 413
















Reviews: