background image

HQ Fusion

 User Manual 1.0 

 Page 8 

Laser Stylus Safety and Use Guidelines 

Theory of Operation 

The laser stylus projects a straight laser beam visible as a dot on surfaces it hits.  The laser 

dot is used as a guide or stylus allowing you to stitch the same pattern onto a quilt that is being 

traced with the laser dot. 

Laser Operation and Use 

There is not a separate on/off switch for the laser.  Power is supplied to the laser when it is 

plugged into the HQ Fusion™.  Be sure the laser is attached to the HQ Fusion™ and pointed 

downward toward the table before connecting it to the port.  Never point it in a direction that 

would project the beam into someone’s eyes.  If the laser should cease to operate, check to 

ensure the plug is firmly seated into the HQ Fusion™ laser port. 

Caution:  

Use of controls or adjustments or performance of procedures other than those 

specified herein may result in hazardous radiation exposure. 

Laser Focus/Laser Image Size 

This high quality laser is focusable. The laser is focused by simply grasping the threaded 

housing surrounding the lens and turning clockwise or counter clockwise 

(see Photo 7). The laser image can be adjusted bigger or smaller. The 

direction of rotation needed is determined by the distance of the laser 

from the intended focal plane. Experiment by turning the threaded end to 

achieve your desired focal size. 

Clamp Adjustment 

The laser attaches to a mounting post. The post may be vertical or 

horizontal. The clamp is designed to articulate any direction by rotating 

the clamp on the post and pivoting the laser up or down. To make an 

adjustment, simply loosen the black thumbscrews, position, and retighten. 

Location of Laser Labels 

The label is attached to the case of the laser and contains an arrow which 

indicates the direction the laser light will shine when energized. The label 

must remain in place on the laser. Removal of the label will void the 

laser’s warranty. 

Photo 7 

Summary of Contents for HQ 24 Fusion































Reviews: